Loop wire starter

Reference: AIG-125

T-handles wire threader

Just lay the wire in the notched tip and pass it through the polyurethane by pushing the tool from the inside to the outside.In the way, you can release the window. Always place the flat surface of the wire threader on the window, so that the hollow tube is not deformed.- 120 x 26 x 10 mm - 20 g

Reference: ZLN-914

Nylon wire - Ø 1.05 mm, Longueur : 100 ML - 2000 Newton

- Multi-purpose with 1 length (approx. 2 to 4 uses) - Does not scratch surfaces - No snags on the windscreen bay or windscreen seal - Can be used with all ratchet systems - Very fine Ø 1.05 mm, Length: 100 M 2000 Newton

Reference: BOB-1.5-ROLL-OUT

Round wire in a spool REPAREGLASS - ø 0,80 mm, 1500 ml

Round wire in a spool The round profile and the small diameter make this wire a real problem solver for todays cars with narrow gaps between glass and body. It has the same high tensile strength than the VKD-44but offers at the same time as much lower risk to damage interior linings and dashboards.679 Newtonø 0,80 mm, 1500 ml

Reference: AIG-789

Straight wire threader

Many technicians remove windshields by starting the wire through the top and bottom center of the windshield, then cutting towards each side. So as to push the cutting wire into the urethane, especially where there is a wide surface of urethane, we recommend using the wire threader. The slot (1,2 mm only) and the cutting wire are pushed together into the...

Reference: VKD-44A

Brand: REPAREGLASS

SQUARED CUTTING WIRE in a spool- Size: 0.6mm - 44 ML

SQUARED CUTTING WIRE in a spool REPAREGLASS Surprising but true! The cutting resistance of the squared wire is far higher than the one of the common round wire. Try it, you will see!Squared wire - 0,6 x 0,6 mm,- length: 44m, on plastic spool.- 100 x 22 mm - 110 g

Reference: XKD-22A

New square cutting wire, Size 0.7 mm - 22ML

Reference: SD-22

Braided wire in a spool - - ø 0,80 mm - 22ML

Braided wire in a spool REPAREGLASS ø 0.80 mm, length: 22 m, Wound on a plastic spool. 1083 NEWTON The wire to be cut is twisted according to our exact specifications from three strong stainless steel wires. The wire is anodised in a typical "gold" colour.

Reference: PAIG-200

Wire gripping handles (corkscrew shape)

Wire gripping handlesIdeal solution to work rapidly and without problem. Feed the wire through the hole in the wedge shaft (fig A), loop it through the hole at the top of the shaft (fig B) and then bring it back into the large plastic handle. By pressing the wedge back into the handle, the wire is held in place (fig C). To shorten the wire, press down on...

Reference: WL1135

5 Extra wire loops for Loop wire starter

Extra wire loops for Loop wire starter

Reference: DST-61

Curved wire threader 61 mm (package at 3 pièces)

Curved wire threader:The curved wire threader anables threading of the cutting wire evenwhere the gap between glass and pinch weld is very small.This is especially helpful on side and back windows where conventionalwire threaders are often difficult to use.The curved threader can be pushed through the adhesive bead from insideto outside or from outside to...

Reference: XKD-44A

Brand: REPAREGLASS

Square wire for windshield cutting - 0.7 x 0.7 mm - 44ML

XKD-44 - SQUARE PIANO WIRE - 44M 976 NEWTON Technical characteristics of our new REF-XKD-44 piano wire. - This is a square piano wire with a larger cross-section0.7 x 0.7 mm than the VKD-44 (0.6 x 0.6 mm). - The breaking strength of this rope is 36% higher than that of VKD-44. - Available in 44 ml rolls

Reference: DST-53

Curved wire threader 53 mm (package at 3 pièces)

Curved wire threader:The curved wire threader anables threading of the cutting wire evenwhere the gap between glass and pinch weld is very small.This is especially helpful on side and back windows where conventionalwire threaders are often difficult to use.The curved threader can be pushed through the adhesive bead from insideto outside or from outside to...

Reference: TRI-176

Triangular wire - 0.85mm - 50ML

REF. TRI-176Triangular wire.0,85 x 0,85 mm,Length : 50 metersTensile strength : 691 Newton

Reference: DST-734BUS

T-handle wire threader special bus and trucks

Special wire threader for bus and trucks with 2 holes ( for square or braided wire and nylon wire.) The end of the needle has a special designed in order to introduce easy the wire through the urethane. Push it in the urethane, insert the wire inside the tube, remove the wire threader and lead the wire throughout the urethane, in order to be able to pic...

Reference: DST-58

Curved wire threader 58 mm (package at 3 pièces)

Curved wire threader:The curved wire threader anables threading of the cutting wire evenwhere the gap between glass and pinch weld is very small.This is especially helpful on side and back windows where conventionalwire threaders are often difficult to use.The curved threader can be pushed through the adhesive bead from insideto outside or from outside to...

Reference: DGL-201S

Wire gripping handle with sucker

This handle can be stuck to the glass to go around the vehicles front and grab it from the other side a real good idea and a really handy tool!

Reference: AIG-300

Wire guide

The wire guide's long, narrow shaft allows positioning the wire so it prevents the dash and interior mouldings from being damaged. Recommended above all for cars with a high windshield slope or with a bottom window bond that is hardly accessible. Of course, the wire guide can also be used from the outside.- 350 x 38 x 38 mm - 220 g

Reference: DST-734

T-handle wire threader with hole

REF-DST-734 T-handle wire threader with hole Just lay the wire in the notched tip and pass it through the polyurethane by pushing the tool from the inside to the outside.In the way, you can release the window. Always place the flat surface of the wire threader on the window, so that the hollow tube is not deformed.120 x 26 x 10 mm • 20 g

Reference: GCN-100

Nylon wire - ø 1,1 mm - 100ML

L: 100M 2500 NEWTON Nylon wire- Diam 1.1mm ESPECIALLY DESIGN FOR THICK AND HEAVY PU Ideal for : -Old urethane -Thick and heavy PU -Trims which must not brake ( clips – fastener – spacers) -Brakes at an high tensile strength -Reusable length ( from about 2 to 4 applications) -Do not scratch surfaces -Could be use with most of the ratchet systems...

Reference: DSS-175

One-man wire cut-out tool

One-man wire cut-out toolREPAREGLASSOne-man wire cut-out toolThis tool acts like another person sitting inside the vehicle pulling the wire back after you havemade your cutting stroke.Attached to the swivel is a spring that acts as a second person; you pull the wire out to make your cut and the springs pulls the wire back in. The spring is attached to a...

Reference: VKD-22A

Brand: REPAREGLASS

Squared cutting wire - Size 0.6mm - 22ML

Squared cutting wire REPAREGLASS Surprising, but true! The cutting force of square wire is far superior to that of common round wire. Try it out for yourself, you'll be amazed! REF-VKD-22 Square wire. 0.6 x 0.6 mm, length: 22 m, wound on plastic spool. 691 NEWTON

Reference: AIG-730

T-handles wire threader

Just lay the wire in the notched tip and pass it through the polyurethane by pushing the tool from the inside to the outside.In the way, you can release the window. Always place the flat surface of the wire threader on the window, so that the hollow tube is not deformed.- 120 x 26 x 10 mm - 20

Reference: SD-21

Braided wire - ø 0,80 mm - 22.5M

Braided wire21 ml REPAREGLASSBraided wire The braided wire is made of three stainless steel resistant wires that are braided to one strand. The wire is anodized (with a traditional gold colour). It has a 0.80mm diameter.