copy of Kavisli tel geçirici

Reference: PILE-RAPTOR522

Battery pack for RAPTOR Kit

Battery pack for RAPTOR kit Warning: these batteries are compatible with RAPTOR kits from serial number R0005372 upwards. For kits purchased before this number, you will need to order the reference PILE-RAPTORX4.

Reference: WK2

Average, universal, flat BTB blade, 240mm

Average, universal, flat BTB blade, 240mm

Reference: RR23-CLIQUETRAPTOR

Ratchet for RAPTOR kit

Please note that this ratchet is not compatible with the RAPTOR Kit. 1 Ratchet For ROLL-N-CUT kit

Reference: Z9RV

New Paint Protection Reverse Bend Blade 38mm « ULTRAWIZ »

Nylon coating protects exposed paint from accidental blade contactIdeal for exposed glass with underside molding or encapsulationOffers the control a technician needs to cut awayfrom the glass or moldingAvailable in 3 lengths : 19 mm – 25 mm – 38 mm

Reference: FSL240

Pinchweld scraper with interchangeable blade

Pinchweld scraper with interchangeable bladeThis may be the last pinchweld scraper you will ever buy! From now on.You may just buy blades. When the blade finally wears out, remove the two screws, pull out the old blade, drop in a new blade and tighten the two screws. These pinchweld scrapers are made of spring steel and are hard enough so they will not...

Reference: WK3S

Serrated, multi-purpose, bent BTB blade, 200mm

Serrated, multi-purpose, bent BTB blade, 200mm

Reference: NMT-448

Mechanical pick up

Mechanical pick up The use of telescopic magnet could be sometimes impossible to use because of non ferrous items. It is times like these when you need our Mechanical Pick-Up. It is designed with steel fingers that are spring-loaded that will grip an item up to 2,5 cm in diameter.

Reference: SK120

Replacement blade for fsl 240 pinchweld scraper l:13mm

Replacement blade for fsl 240 pinchweld scraper 13mm wide

Reference: AEB405-N192

Pneumatic knife: Equalizer® EXCALIBUR® DELUXE - 2nd LIFE - N192

Kit in good condition. The case may be incomplete (blades). Only cosmetic defects shown in the photos are present. Only one item available. 2nd LIFE warranty: 6 months Recommended for cutting the lower parts of the windscreen, rear windows and quarter windows. Cutting the interior of the vehicle. Compact and lighter, it is even easier to handle,...

Reference: FSC-350

Brand: REPAREGLASS

Special scraper

REF. FSC-350SCRAPER (without blade)To scrape the old urethane bead. This scraper is universal due to thefact it can accept different blades width ( 13 mm – 16 mm – 20 mm)and angular bladesIts locking system with roll allow a quick and easy blade replacement

Reference: FB121

Cutting blade, straight - 26mm

Cutting blade, straightCutting length: 26 mmSold individually

Reference: WK4S

Serrated, non-rigid, bent BTB blade, 190mm

Serrated, non-rigid, bent BTB blade, 190mm

Reference: 3007-K

Adjustable REPAREGLASS cold knife

The adjustable REPAREGLASS cold knife is designed to offer efficiency, speed, and precision when cutting. Thanks to its adjustment lever, you can extend or retract the blade in one simple movement, easily adjusting the cutting depth without having to unscrew the retaining nut. No more wasted time: this innovative system saves you considerable time while...

Reference: Z11RD

New COLD KNIFE BLADES SERRATED 25mm

REF-Z11RDNew ULTRAWIZ Cold knife bladeSold individually - Extra thin Cutting length: 25 mmCARTON OF 10

Reference: EWA-1702

Windshield wiperarm removal tool

Extremely loadable. Made of massive metal. Can be used on virtually any passenger and commercial vehicle. Specially recommended for the BMW 5 and BMW 7 series.- 104 x 38 x 140 mm- 518 g

Reference: RAPTOR

Windshield cutting system with automatic vacuum - RAPTOR

The  Raptor™ is a cord and wire auto glass removal device designed from the ground-up to dramatically improve the power of the vacuum cup with the integration of our AirForce™ Constant Vacuum Cups. This technology has been specifically developed to create a quick placement and constant vacuum to the glass so the Raptor™ stays in place and resists...

Reference: DESTOCK-AF1009

Self oiling glass cutter

REF-AF1009Self oiling glass cutterDue to the translucent color, you can see how much oil is inthe cutter. It has an end cap with a seal so the oil will not leakfrom the end of the cutter.They are of the highestquality and havebecome one of themost-used glass cuttersin the world.• Sold individually

Reference: LH-683-N144

Lever for hubcaps - 2nd life

In average condition Only a few minor cosmetic defects appear - 1 Only one item available 2nd LIFE warranty: 6 months Removing hubcaps without the right tool can quickly damage these delicate parts. If a flat screwdriver is sometimes used, its small contact surface often causes damage and does not provide sufficient leverage. The hubcap lever solves these...

Reference: DST-734

T-handle wire threader with hole

REF-DST-734 T-handle wire threader with hole Just lay the wire in the notched tip and pass it through the polyurethane by pushing the tool from the inside to the outside.In the way, you can release the window. Always place the flat surface of the wire threader on the window, so that the hollow tube is not deformed.120 x 26 x 10 mm • 20 g

Reference: 252

Water-repellent white grease aerosol - 400ml

A high-performance lubricant to protect and maintain your moving parts. Key features: Thixotropic formula: Ideal for parts subjected to high pressure, shock and oscillation. Provides long-lasting lubrication even under extreme conditions. Excellent adhesion: Stays in place on all surfaces, even during continuous movement. Water- and corrosion-repellent:...

Reference: ULB-582

TRAPEZOIDAL BLADES (x 10 )

Trapezoidal blades ( x 10 )

Reference: FB111

Hook blade with U shape - 95 mm

profondeur de coupe : 95 mmvendue à l' unité

Reference: PH-1355

Spatula curved to remove the clips

Curved Door Upholstery Remover For removing plastic fasteners in confined places. It is the same upholstery remover as the one shown above, but it is instended for use on the front part of the door where the door jam will often interfere with the removal of the door panel. Place the notch in the tool over the fastener and pry the fastener out the hole. It...

Reference: ENK148

Pneumatic knife: EQUALIZER ® Ninja deluxe

The Equalizer® Ninja Deluxe kit is the essential tool for glass professionals for fast, precise and efficient cold cutting. Suitable for all types of vehicles, this pneumatic knife combines power, ergonomics and maneuverability, with up to 22,000 oscillations per minute for effortless work, even in the most complex areas. Key features: Exceptional...

Reference: SC320

20mm scraperblades for ref. FSC-300SPECIAL

Reference: FBS129

Scraper blade set

Jeu de 2 lames à racler. l'une large de 12 mm, l'autre de 25 mm

Reference: FICEL9M

String of 9 meters for TB-102

String of 9 meters for TB-102 (Rope insert tool).

Reference: LM-460

Long knife with a blade

Long knife with 1 blade Some vehicles have extra-long dashes. So you have to cut the bond from the inside. As long as the band of urethane is not too thick, you can use knives designed to cut urethane. Two lengths are available: 46 cm (standard) and 61 cm (designed for vehicles with a high windshield slope and with ewtra-long dashes). Both are made of...

Reference: CROR-S

Brand: REPAREGLASS

Ball-tipped hook, with short shaft

Ball-tipped hook, with short shaft- 210 x 35 x 35 mm - 122 g

Reference: TKS-100

Trapezoid blades

Trapezoid blades. In a pratical dispenser. Our replacement blades for utility knives are 0,6 mm thick, so they are very sturdy. These blades are in a safety dispenser with a suspension hook so as to avoid any risk of injury. You take new blades by sliding them out from the above side of the dispenser while youdispose of the worn out blades by sliding them...