So?uk b?çak, ekstra ince 38 mm

Reference: CAISSE-N396

Storage case L: 44 cm x H: 17 cm x W: 19 cm - 2nd LIFE - N396

In very good condition Only a few minor cosmetic flaws - 1 Only one item available 2nd LIFE warranty: 6 months Storage case Length: 44cm - Width: 17cm - Height: 19cm

Reference: LAME-DECOUPE-NINJA

Cold cutting blade: Equalizer Ninja

Specially designed for the Equalizer® Ninja pneumatic knife, these cold cutting blades offer optimal precision and remarkable efficiency, suitable for use on all types of windshields. Their design absorbs vibrations while ensuring a clean and fast cut, even in the most difficult-to-reach areas.

Reference: XL2-N95

Olfa ® long knife with breakable blade - 2nd life

In good condition Only a few minor cosmetic flaws - 1 Only one item available 2nd LIFE warranty: 6 months Breakaway blades have been growing in popularity in our industry for several years. It quickly became apparent that a knife equipped with this type of blade would be ideal for cutting the bottom adhesive strip when working on automotive glass. With...

Reference: LH-683-N113

Lever for hubcaps - 2nd life

In good condition Only a few minor cosmetic defects appear - 1 Only one item available 2nd LIFE warranty: 6 months Removing hubcaps without the right tool can quickly damage these delicate parts. If a flat screwdriver is sometimes used, its small contact surface often causes damage and does not provide sufficient leverage. The hubcap lever solves these...

Reference: XL2-N140

Olfa ® long knife with breakable blade - 2nd life

In average condition Only a few minor cosmetic flaws - 1 Only one item available 2nd LIFE warranty: 6 months Breakaway blades have been growing in popularity in our industry for several years. It quickly became apparent that a knife equipped with this type of blade would be ideal for cutting the bottom adhesive strip when working on automotive glass. With...

Reference: VNT-306

EQUALIZER® top notchtm tool

Urethane nozzle tool, top notchTM tool This tool allows you to cut rapidly and easily a proper V-notch on a urethane nozzle. This is important for an effective work! Indeed, before applying bond, a proper notch has to be cut. To use this tool, take a knife and cut the end of the nozzle tip to give yourself a bead. Next insert the top NotchTM tool inside...

Reference: WK24

Long, deep offset, BTB blade, 240mm

Long, deep offset, BTB blade, 240mm

Reference: Z3

Cold knife blade 38 mm

Cold knife blade, extra fine- Sold individually- Cutting length: 38 mm- 20 gCARTON OF 10

Reference: WK24Z

Deep offset, BTB blade, 150mm

Deep offset, BTB blade, 150mm

Reference: LM-460

Long knife with a blade

Long knife with 1 blade Some vehicles have extra-long dashes. So you have to cut the bond from the inside. As long as the band of urethane is not too thick, you can use knives designed to cut urethane. Two lengths are available: 46 cm (standard) and 61 cm (designed for vehicles with a high windshield slope and with ewtra-long dashes). Both are made of...

Reference: FSC1.7BAT

FEIN battery knife - without blade, without battery

Discover an innovative, high-performance solution for automotive work, combining power, precision and practicality. Technical specifications: Battery voltage: 18 V Battery capacity: 5 Ah Oscillations: 10,000 - 19,500 rpm Weight with battery: 1.8 kg Amplitude: 2 x 1.7 Tool holder: hexagonal Please note: Supplied without blade, battery or charger. -...

Reference: Z5

Cold knife blade, extra fine 25 mm

Cold knife blade, extra fine - Sold individually - Cutting length: 25 mm - 18g CARTON OF 10

Reference: LH-683-N144

Lever for hubcaps - 2nd life

In average condition Only a few minor cosmetic defects appear - 1 Only one item available 2nd LIFE warranty: 6 months Removing hubcaps without the right tool can quickly damage these delicate parts. If a flat screwdriver is sometimes used, its small contact surface often causes damage and does not provide sufficient leverage. The hubcap lever solves these...

Reference: FSL240

Pinchweld scraper with interchangeable blade

Pinchweld scraper with interchangeable bladeThis may be the last pinchweld scraper you will ever buy! From now on.You may just buy blades. When the blade finally wears out, remove the two screws, pull out the old blade, drop in a new blade and tighten the two screws. These pinchweld scrapers are made of spring steel and are hard enough so they will not...

Reference: SD-22

Braided wire in a spool - - ø 0,80 mm - 22ML

Braided wire in a spool REPAREGLASS ø 0.80 mm, length: 22 m, Wound on a plastic spool. 1083 NEWTON The wire to be cut is twisted according to our exact specifications from three strong stainless steel wires. The wire is anodised in a typical "gold" colour.

Reference: 238-N165

Storage case L: 40 cm x H: 20 cm x W: 20 cm - 2nd LIFE - N165

In good condition Only a few minor cosmetic defects appear - 1 Only one item available 2nd LIFE guarantee: 6 months Storage case Length: 40 cm - Width: 20 cm - External height: 20 cm - Internal depth: 15 cm.

Reference: DSS-175

One-man wire cut-out tool

One-man wire cut-out toolREPAREGLASSOne-man wire cut-out toolThis tool acts like another person sitting inside the vehicle pulling the wire back after you havemade your cutting stroke.Attached to the swivel is a spring that acts as a second person; you pull the wire out to make your cut and the springs pulls the wire back in. The spring is attached to a...

Reference: Z60

Special cold knife blade 60 mm

This blade series enables you to use a cold knife where you could never use it before ! The 60 mm long blade is intended to cut all those hard to reach PU bondings thatare far away from the glasses edge and where a normalcold knife blade could never reach. But also all lowerglass edges with surmounting wings and bonnets are aperfect field of application...

Reference: AIG-789

Straight wire threader

Many technicians remove windshields by starting the wire through the top and bottom center of the windshield, then cutting towards each side. So as to push the cutting wire into the urethane, especially where there is a wide surface of urethane, we recommend using the wire threader. The slot (1,2 mm only) and the cutting wire are pushed together into the...

Reference: Z30

Special cold knife blade 30 mm

This blade series enables you to use a cold knife where you could never use it before ! The 60 mm long blade isintended to cut all those hard to reach PU bondings that are far away from the glasses edge and where a normalcold knife blade could never reach. But also all lowerglass edges with surmounting wings and bonnets are aperfect field of application...

Reference: L2

Olfa® knife

Olfa®knife This knife is made of high impact plastic, has a stainless steel blade housing and a positive locking thumb wheel so that you can set the blade at any length. The back of the knife features a rubber grip that lets the knife rest comfortably in your hand and keeps it from slipping. The famous model. - 146 x 40 x 20 mm - 110 g

Reference: BOB-1.5-ROLL-OUT

Round wire in a spool REPAREGLASS - ø 0,80 mm, 1500 ml

Round wire in a spool The round profile and the small diameter make this wire a real problem solver for todays cars with narrow gaps between glass and body. It has the same high tensile strength than the VKD-44but offers at the same time as much lower risk to damage interior linings and dashboards.679 Newtonø 0,80 mm, 1500 ml

Reference: PAIG-200

Wire gripping handles (corkscrew shape)

Wire gripping handlesIdeal solution to work rapidly and without problem. Feed the wire through the hole in the wedge shaft (fig A), loop it through the hole at the top of the shaft (fig B) and then bring it back into the large plastic handle. By pressing the wedge back into the handle, the wire is held in place (fig C). To shorten the wire, press down on...

Reference: FSC-300SPECIAL

Brand: REPAREGLASS

Special scraper

REF. FSC-300SPECIALSCRAPER (without blade)To scrape the old urethane bead. This scraper is universal due to thefact it can accept different blades width ( 13 mm – 16 mm – 20 mm)and angular blades

Reference: AEB405-N195

Pneumatic knife: Equalizer® EXCALIBUR® DELUXE - 2nd LIFE - N195

Kit in good condition. The case may be incomplete (blades). Only cosmetic defects shown in the photos are present. Only one item available. 2nd LIFE warranty: 6 months Recommended for cutting the lower parts of the windscreen, rear windows and quarter windows. Cutting the interior of the vehicle. Compact and lighter, it is even easier to handle,...

Reference: WKBX

Specific case for BTB material

SPECIFIC CASE FOR BTB MATERIALREF. WKBX

Reference: TRI-176

Triangular wire - 0.85mm - 50ML

REF. TRI-176Triangular wire.0,85 x 0,85 mm,Length : 50 metersTensile strength : 691 Newton

Reference: FB209

Hook blade with L shape - 38 mm

profondeur de coupe : 38 mmvendue à l'unité

Reference: SD-21

Braided wire - ø 0,80 mm - 22.5M

Braided wire21 ml REPAREGLASSBraided wire The braided wire is made of three stainless steel resistant wires that are braided to one strand. The wire is anodized (with a traditional gold colour). It has a 0.80mm diameter.

Reference: SGR-380-N120

Window scraper, with 1 blade RK -100A - 2nd life

In good condition - red in color Only a few minor cosmetic defects appear - 1 Only one item available 2nd LIFE guarantee: 6 months An essential tool for quickly and efficiently preparing glass surfaces, this scraper is mainly used to thoroughly remove adhesive residue before reinstalling glass. It can also be used as a scraper to remove labels or other...