VBSA awarded ECOVADIS label
Banner
Vacuum lifterØ 150 mm REPAREGLASS
These vacuum lifter have been specially designed for windsheild setting and removal.
Their unique shape allows a good hand holding.
The flowing shape and the smooth surface of the handles allow a greater control of large windows.
To install a windshield, we ercommend beginning by doing a test.
The setting of the windsheild will then be facilitated, with less risk of positioning it wrong.
One of the vacuum lifters should be placed as far away from the lateral side as possible, so that you can use your forearm and shoulder, avoiding in this way stress on your body.
The two vacuum lifters should be placed as far away as possible from one another, while keeping a good control of the window.
The tightening of the piston rod has to be done until you cannot see the red line anymore.
Secure payment
FREE SHIPPING from 150,00 € H.T. (France métropolitaine)
Certified organization
Vacuum lifterØ 150 mm REPAREGLASS
These vacuum lifter have been specially designed for windsheild setting and removal.
Their unique shape allows a good hand holding.
The flowing shape and the smooth surface of the handles allow a greater control of large windows.
To install a windshield, we ercommend beginning by doing a test.
The setting of the windsheild will then be facilitated, with less risk of positioning it wrong.
One of the vacuum lifters should be placed as far away from the lateral side as possible, so that you can use your forearm and shoulder, avoiding in this way stress on your body.
The two vacuum lifters should be placed as far away as possible from one another, while keeping a good control of the window.
The tightening of the piston rod has to be done until you cannot see the red line anymore.
Reference: GEZ-150-1
Vacuum lifterØ 150 mm REPAREGLASSThese vacuum lifter have been specially designed for windsheild setting and removal.Their unique shape allows a good hand holding. The flowing shape and the smooth surface of the handles allow a greater control of large windows.To install a windshield, we ercommend beginning by doing a test. The setting of the windsheild...
Reference: GEZ-543-1
Vacuum lifterØ 150 mmREPAREGLASSThese vacuum lifter have been specially designed for windsheild setting and removal.Their unique shape allows a good hand holding. The flowing shape and the smooth surface of the handles allow a greater control of large windows.To install a windshield, we ercommend beginning by doing a test. The setting of the windsheild...
Reference: VP-230SPECIALE
Vacuum lifter Ø 230 mm (in a plastic case)Bell-shaped rubber pad with multiple – seal lip. For optimum hold. To fix with the integrated vacuum pump.Red safety ring at the pump plunger enables optical monitoring of the vacuum. Load capacity for the lifter is 350 kg REF-VP-230SPECIALE•Sold individually• Load capacity around 350 kgØ 230 mmDelivered in a...
Reference: PSH-120-VERIBOR
VERIBOR SUCTION CUP PAIR.REF. PSH-120-VERIBOR• Ø 120 mm : Loading capacity : 80 kg
Reference: FRE-080-P
Moulding hold down toolThe corners on mouldings will often raise up and leave an unsightly gap under them. Taping these mouldings down can be disastrous because the tape will sometimes attack then paint and, in the worst case, remove it. This moulding hold down tool is attached with a vaccum cup. Pressure is then applied to each end of the tool by...
Reference: RL-1382
Windshields adjustment suction cupStops the windshield in the correct place. ere is a simple solution to one ofthe most annoying problems a technician faces today.When a vehicle does not have stops it is difficult for one person to set thewindshield because he does not have anything to set it on.Here is the solution, before removing the old windshield put...
Reference: PSL-150-1
Suction cup deluxe sold individualy (Ø 150 mm)Easier and safer to attach that common suction lifters with clamp lever technology.The bell shaped rubber pads already adhere onto the glass surface with slight pressing even before pressing the lever.Possibility to pass a belt through. Load capacity for each lifter is 80 kg.
Reference: PSL-150-1VERIBOR
VERIBOR SUCTION CUPREF-PSL-150-1VERIBOR• Ø 150 mm : Loading capacity : 80 kg
Reference: VP-205
Vacuum lifter Ø 205 mm (in a plastic case)Bell-shaped rubber pad with multiple – seal lip. For optimum hold. To fix with the integrated vacuum pump. Red safety ring at the pump plunger enables optical monitoring of the vacuum. Load capacity for the lifter is 260 kgSold individually Delivered in a case
Reference: VP-230
Vacuum lifter Ø 230 mm(in a plastic case) Bell-shaped rubber pad with multiple seal lip.For optimum hold, also on strongly curved glasssurfaces.To fix with the integrated vacuum pump.Red safety ring at the pump plunger enables optical monitoring of the vacuum. Load capacity for the lifter is 120 kgDelivered in a plastic case.
Reference: 9005B
Dent suction cup. Grips very well on any surface (car body, glass, hood–).- Diameter: 115mm- Load capacity: 40kg- Sold individually
Reference: RL-170
Suction cup with handle diameter 70 mmDurable quality suction cup. Adaptable on glass, marble, ceramic.Ideal to remove and install quarter glass.Loading capacity : 12 kgREF. RL-170Sold individually
Reference: VP-2075
Sold individually - delivered in a case
Vacuum lifterØ 150 mm REPAREGLASS
These vacuum lifter have been specially designed for windsheild setting and removal.
Their unique shape allows a good hand holding.
The flowing shape and the smooth surface of the handles allow a greater control of large windows.
To install a windshield, we ercommend beginning by doing a test.
The setting of the windsheild will then be facilitated, with less risk of positioning it wrong.
One of the vacuum lifters should be placed as far away from the lateral side as possible, so that you can use your forearm and shoulder, avoiding in this way stress on your body.
The two vacuum lifters should be placed as far away as possible from one another, while keeping a good control of the window.
The tightening of the piston rod has to be done until you cannot see the red line anymore.
