Banner
Banner
There are 14 products.
Reference: 432
Hand cleaner cream.No sand, no solvent. Since it contains adipose and protecting components, it is not irritating for the skin. Leaves a -cream effect- on the hands. Contains a regulating and epidermis-restoring agent.Itcontains no sand, no dephosphate, no solvent, so it respect the environment. Antiseptic.10 litre bucket
Reference: 433
Cleaning gel made of vegetable microballsThis skin gel with vegetable microballs is efficient against specific dirt (paint, bond, inks, resins, lacquers). It is biodegradable and respects the environment.Meets the AFNOR NFT 73-102 norms.1-litre boxMeets the AFNOR NFT73-102 norms Extractor -soap: DIST1-SAV
Reference: BDA-251
Footloose Rubber Gasket Release Tool Here is a great solution to a frustrating problem. Many vehicles have large, rubber-set windshields. The common method to remove these windshields is to put your feet against the glass and push while releasing the rubber gasket with a hook tool. The problem with this is the distance can be so great that you cannot...
Reference: ISH-691
Handle for instalation stick (delivered without stick)MS-180 / MS-182 The installation stick is locked with a screw .
Reference: LB-780
Inflator setThis set allows to facilitate the cutting of the urethane bead by giving pressureon the glass in the outside direction from where the urethane is already cutted.This set protects against neck pain, due to the fact most of the glass installerstend to push out the windshield with their head from inside to outside in orderto get more space to cut...
Reference: MS-180
Installation stickThe installation stick has been used for more than 30 years to place seals for glass on cars. The stick is made in non-adhesive plastic, so the polyurethane can easily be removed from the plastic surface. Thus, this tool is used to place rubber joints or polyurethane beads.- 200 x 18 x 7 mm - 20 g
Reference: MS-182
Installation stick with one round end shape and one flat end shape The installation stick has been used for more than 30 years to place seals for glass on cars. The stick is made in non-adhesive plastic, so the polyurethane can easily be removed from the plastic surface. Thus, this tool is used to place rubber joints or polyurethane beads.
Reference: NS-362
Many windshields today must be cut out from the inside. This is specially true when the urethane is above the bottom edge of the glass, but below the dash. Many technicians use their head to push against the glass while they are cutting the urethane. This can cause damage to the neck and should never be done. Avoid this and use our necksaverTM!™- 215 x...
Reference: OUV-CART
Urethane tube openerOpen properly and safely your urethane tubes by using the tube opener. Press the rear of the tube over the serrated circle to remove the rear seal. Then turn the tube over and press the front seal into the pointed stem and your tube of urethane is ready to use. The openers is made of urethane-resistant material, so you can easily...
Reference: SB-880
Safety glassesIt is absolutely necessary to wear safety glasses when you work with windows. These impact-resistant safety glasses fit comfortably over most prescription eyewear. An advenced desingn holds well and protects all around the eyes.- 170 x 70 x 40 mm - 44 g
Reference: SSU-190
Universal sharpening stone with handleWith this sharpening stone, you sharpen worn-out blades with no danger for your hands. Particularly recommended for a perfect sharpening ofcold knives or other blades.- 172 x 35 x 25 mm - 65 g
Reference: TSP-292
Tight spots ( set of 2 units )Some places, such as parking garages and small parkinglots, have vehicles parked close together and it is not alwayspossible to move them to another place.They are made of apiece of dense foam rubber on one side and a soft vacuum cupon the other side. The foam or the vacuum cup will not damagea vehicle. To use them just stick...
