Reference: ZAW-120
Windshield wiper arm removal tool
Extremely loadable. Made of massive metal. Can be used on virtually any passenger and commercial vehicle. Specially recommended for the BMW 5 and BMW 7 series.- 104 x 38 x 140 mm- 518 g
- NEW PRODUCTS
- SECOND CHOISE
- DESTOCKING
- REPAIR
- BONDING
- DIAGNOSTIC & CALIBRATION TOOL
- TOOLS
- Workshop layout
- Windshield installation tools
- Windscreen tools kits
- Protection
- Clips and fasteners
- Clips and fasteners kits
- Universals clips et fasteners
- ALFA ROMEO Clips and fasteners
- Clips et agrafes RENAULT
- AUDI Clips and fasteners
- BMW Clips and fasteners
- CITROEN Clips and fasteners
- DACIA Clips and fasteners
- DAF Clips and fasteners
- FIAT Clips and fasteners
- FORD Clips and fasteners
- HONDA Clips and fasteners
- IVECO Clips and fasteners
- LANCIA Clips and fasteners
- LAND ROVER Clips and fasteners
- MERCEDES Clips and fasteners
- MINI Clips and fasteners
- MITSUBISHI Clips and fasteners
- NEOPLAN Clips and fasteners
- NISSAN Clips and fasteners
- OPEL Clips and fasteners
- PEUGEOT Clips and fasteners
- SEAT Clips and fasteners
- SKODA Clips and fasteners
- VOLVO Clips and fasteners
- VW Clips and fasteners
- Windshield fixing
- Windshield lifting
- SMART REPAIR
- BODY REPAIR
- MISCELLANEOUS
-
VBSA awarded ECOVADIS label
-
Banner
Windshield wiper arm removal tool Universal
WFA-450
REF. WFA-450
Universal Wiper Puller. Sometimes you need a
large thick puller arm to remove a windshield wiper
and sometimes you need a small thin arm. This is the
reason our wiper puller has interchangable arms. Set
the wiper puller arms on the horozontal slide, slide
them in until they touch the side of the windshield
wiper, snug the wing nut to hold them in place, use
a wrench or ratchet to tighten the bolt that contacts
the wiper nut and you can remove most windshield
wipers. Each tool contains two sets of interchangable
jaws. The entire tool is made of hardened steel to give
you years of carefree use.
Secure payment
FREE SHIPPING from 150,00 € H.T. (France métropolitaine)
Certified organization
Description
REF. WFA-450
Universal Wiper Puller. Sometimes you need a
large thick puller arm to remove a windshield wiper
and sometimes you need a small thin arm. This is the
reason our wiper puller has interchangable arms. Set
the wiper puller arms on the horozontal slide, slide
them in until they touch the side of the windshield
wiper, snug the wing nut to hold them in place, use
a wrench or ratchet to tighten the bolt that contacts
the wiper nut and you can remove most windshield
wipers. Each tool contains two sets of interchangable
jaws. The entire tool is made of hardened steel to give
you years of carefree use.
Product Details
WFA-450
Data sheet
- Packaging
- PIECE
11 other products in the same category:
Reference: WFA-500
Arm Wiper puller
REF. WFA-500Arm Wiper pullerArm wiper puller especially designed forVolkswagen rear window models, Audi, Skoda,Seat, but also many others.Untight the button from the arm but do not release it( could caused damages on the plasticcompartments of the arm.) Position the jaw on thearm of the wiper, tight manually first, then use aratchet 3/8 to strongly tight...
Reference: TE-125
Torx t80 for arms of windshield pullers
This very wide piece is recommended for windshield removal on the BMW 5 and BMW 7 series.- 35 x 18 x 18 mm - 38 g
Reference: ZAW-040
Arm wiper puller tool
REF. ZAW-040Arm wiper puller toolArm wiper puller tool with tighting screw for a simpleuse ( without additional tool)Adaptable for many cars
Reference: ZAW-010
Wiper puller for bolted-on wipers
Wiper puller for bolted-on wipersBecause windshield wipers have become larger, wiper arms are pressure-fitted to the posts so they will not slip. They are then secured with a nut to hold the arm in place so they will not lift. Until now, it was almost impossible to remove these wiper arms without breaking or damaging them or scratching the cowl. You no...
Reference: WFA-450SPECIAL
Universal Wiper Puller
REF-WFA-450SPECIALSimilar to WFA-450 butendowed with double arm
Reference: MSP-211
BOX EXTRACTOR
Arm wiper pullers kit If you remove a bolted on windshield wiper a few months after the vehicle was builtthen it is usually not difficult to remove, but try removing the wiper arm two or threeyears after it was built. It can be almost impossible because manufacturers use onetype of metal on the wiper arm and a different type of metal on the wiper post. If...
Reference: WFA-525
Arm wiper puller for rearwindows.
Arm wiper puller for rearwindows.To avoid to damage the arm wipersfrom rear vehicules, which are oftendamage with traditional arm wiper pullersEx: Peugeot 307-207, Renaultclio III, Espace Laguna, Megane,Nissan Micra et primera
Reference: EWA-1702
Windshield wiperarm removal tool
Extremely loadable. Made of massive metal. Can be used on virtually any passenger and commercial vehicle. Specially recommended for the BMW 5 and BMW 7 series.- 104 x 38 x 140 mm- 518 g
REF. WFA-450
Universal Wiper Puller. Sometimes you need a
large thick puller arm to remove a windshield wiper
and sometimes you need a small thin arm. This is the
reason our wiper puller has interchangable arms. Set
the wiper puller arms on the horozontal slide, slide
them in until they touch the side of the windshield
wiper, snug the wing nut to hold them in place, use
a wrench or ratchet to tighten the bolt that contacts
the wiper nut and you can remove most windshield
wipers. Each tool contains two sets of interchangable
jaws. The entire tool is made of hardened steel to give
you years of carefree use.