VBSA awarded ECOVADIS label
Banner
There are 27 products.
Reference: JP135
JetPacks'" EQUALIZER vacuum cups were designed from the ground-up to eliminate the need for manual pumping. Turn on theJetPacks'", place them on the glass and let them handle the pumping. If the cup loses vacuum, AIR FORCE'" vacuum technology takes over and keeps that crucial suction going until the cup has maximum vacuum again. JetPacks™ has a 175mm...
Reference: PSH-120
Pairof suction cups (Ø 120 mm)Vacuum cups allow you to hold safely a window that is ready to install. The edge of the window must not be touched once the window is ready for the installation. Each vacuum swivels up and down approximately 30° to fit radically contoured glass. Simply set the vacuum cups in place and push the thumb latches down to engage the...
Reference: PSL-150-1
Suction cup deluxe sold individualy (Ø 150 mm)Easier and safer to attach that common suction lifters with clamp lever technology.The bell shaped rubber pads already adhere onto the glass surface with slight pressing even before pressing the lever.Possibility to pass a belt through. Load capacity for each lifter is 80 kg.
Reference: PSH-120-VERIBOR
VERIBOR SUCTION CUP PAIR.REF. PSH-120-VERIBOR• Ø 120 mm : Loading capacity : 80 kg
Reference: PSL-150-1VERIBOR
VERIBOR SUCTION CUPREF-PSL-150-1VERIBOR• Ø 150 mm : Loading capacity : 80 kg
Reference: VP-230
Vacuum lifter Ø 230 mm(in a plastic case) Bell-shaped rubber pad with multiple seal lip.For optimum hold, also on strongly curved glasssurfaces.To fix with the integrated vacuum pump.Red safety ring at the pump plunger enables optical monitoring of the vacuum. Load capacity for the lifter is 120 kgDelivered in a plastic case.
Reference: VP-230SPECIALE
Vacuum lifter Ø 230 mm (in a plastic case)Bell-shaped rubber pad with multiple – seal lip. For optimum hold. To fix with the integrated vacuum pump.Red safety ring at the pump plunger enables optical monitoring of the vacuum. Load capacity for the lifter is 350 kg REF-VP-230SPECIALE•Sold individually• Load capacity around 350 kgØ 230 mmDelivered in a...
Reference: VP-205
Vacuum lifter Ø 205 mm (in a plastic case)Bell-shaped rubber pad with multiple – seal lip. For optimum hold. To fix with the integrated vacuum pump. Red safety ring at the pump plunger enables optical monitoring of the vacuum. Load capacity for the lifter is 260 kgSold individually Delivered in a case
Reference: GEZ-543-1
Vacuum lifterØ 150 mmREPAREGLASSThese vacuum lifter have been specially designed for windsheild setting and removal.Their unique shape allows a good hand holding. The flowing shape and the smooth surface of the handles allow a greater control of large windows.To install a windshield, we ercommend beginning by doing a test. The setting of the windsheild...
Reference: 9005B
Dent suction cup. Grips very well on any surface (car body, glass, hood–).- Diameter: 115mm- Load capacity: 40kg- Sold individually
Reference: GEZ-150-1
Vacuum lifterØ 150 mm REPAREGLASSThese vacuum lifter have been specially designed for windsheild setting and removal.Their unique shape allows a good hand holding. The flowing shape and the smooth surface of the handles allow a greater control of large windows.To install a windshield, we ercommend beginning by doing a test. The setting of the windsheild...
Reference: VSP-290
Window holders (forside windows)Hold up the door glass while you work. Simply loop the cable over the door frame and attach the suction cups to each side of the glass.- 177 x 200 x 76 mm - 70 g
Reference: RL-170
Suction cup with handle diameter 70 mmDurable quality suction cup. Adaptable on glass, marble, ceramic.Ideal to remove and install quarter glass.Loading capacity : 12 kgREF. RL-170Sold individually
Reference: RL-1382
Windshields adjustment suction cupStops the windshield in the correct place. ere is a simple solution to one ofthe most annoying problems a technician faces today.When a vehicle does not have stops it is difficult for one person to set thewindshield because he does not have anything to set it on.Here is the solution, before removing the old windshield put...
Reference: DESTOCK-FRE-080-P
Sold individually Moulding hold down tool To prevent the corners of wheel trims from sticking out, they are often fixed with adhesive tape. But this can react chemically with the vehicle's paintwork and damage it. The solution is offered by our retaining tool, which is fixed to the bodywork with an integrated suction cup and holds the hubcap in place with...
Reference: RTD-499
Pair of ratcheting tie downsRatcheting tie downs are used by glaziers to secure freshly bonded-in glasses.Use these ratcheting tie downs together with our suction cups so as to hold vertical-glazed glasses in place while the urethane cures. The ratcheting tie downs are simply passed through the handles of the vacuum cups and tight-ened.- 165 x 165 x 10 mm...
Reference: VP-2075-DESTOCK
Sold individually - delivered in a case Suction cup with piston to create vacuum Load-bearing capacity: 200 kg Diameter: 207 mm
Reference: PE24
Sold on its own without the suction cup. Recharges via USB-C
Reference: KIT-VP-230-E
KIT consisting of a suction cup (REF.VP-230), 2 lithium batteries 3W- 3.7V (REF.VP-230-E-BAT) and a charger (REF.VP-230-E-CHARG). Diameter: 200mm, Flat suction cup, cannot be used on curved glass. Ideal for flat windscreens such as lorries, buses, etc. Standard suction= 160kg Maximum vertical suction = 180 kg Maximum horizontal suction= 200 kg Charger and...
Reference: VP-230-E-CHARG
Charger for automated suction cup VP-230-E
Reference: VP-230-E-BAT
Battery for automated suction cup VP-230-E, with charge indicator.
Reference: DESTOCK-RTD-599
Pair of ratchet clamping straps. Clamping straps are used to great advantage by glaziers to secure newly installed panes. Use these straps together with our suction cups to hold vertically mounted panes in the desired position. The straps are simply passed over the handles of the suction cups and tightened as required.
