VBSA awarded ECOVADIS label
Banner
Windshields adjustment suction cup
Stops the windshield in the correct place. ere is a simple solution to one of
the most annoying problems a technician faces today.
When a vehicle does not have stops it is difficult for one person to set the
windshield because he does not have anything to set it on.
Here is the solution, before removing the old windshield put the hood all the
way down. Set the stop on the windshield engage the vacuum and mark the
place where the stop should go.
Windshields adjustment suction cup
Stops the windshield in the correct place. ere is a simple solution to one of
the most annoying problems a technician faces today.
When a vehicle does not have stops it is difficult for one person to set the
windshield because he does not have anything to set it on.
Here is the solution, before removing the old windshield put the hood all the
way down. Set the stop on the windshield engage the vacuum and mark the
place where the stop should go.
Reference: 252
A high-performance lubricant to protect and maintain your moving parts. Key features: Thixotropic formula: Ideal for parts subjected to high pressure, shock and oscillation. Provides long-lasting lubrication even under extreme conditions. Excellent adhesion: Stays in place on all surfaces, even during continuous movement. Water- and corrosion-repellent:...
Reference: PSH-120
Pairof suction cups (Ø 120 mm)Vacuum cups allow you to hold safely a window that is ready to install. The edge of the window must not be touched once the window is ready for the installation. Each vacuum swivels up and down approximately 30° to fit radically contoured glass. Simply set the vacuum cups in place and push the thumb latches down to engage the...
Reference: PSH-120-VERIBOR
VERIBOR SUCTION CUP PAIR.REF. PSH-120-VERIBOR• Ø 120 mm : Loading capacity : 80 kg
Reference: PSH-120-1-N69
Suction cup in very good condition - Please note: sold individually Only cosmetic defects shown in the photos are present - 1 Only one item available 2nd LIFE warranty: 6 months The suction cup allows you to lift a window pane that is ready to be installed safely (2 are required). The edge of the window pane must not be touched after it has been prepared...
Reference: PSH-120-1-N23
Suction cup in good condition - Please note: sold individually Only cosmetic defects shown in the photos are present - 1 Only one item available 2nd LIFE warranty: 6 months The suction cup allows you to lift a window pane that is ready to be installed safely (2 are required). The edge of the window pane must not be touched after it has been prepared for...
Reference: GEZ-150-1
Vacuum lifterØ 150 mm REPAREGLASSThese vacuum lifter have been specially designed for windsheild setting and removal.Their unique shape allows a good hand holding. The flowing shape and the smooth surface of the handles allow a greater control of large windows.To install a windshield, we ercommend beginning by doing a test. The setting of the windsheild...
Reference: PSH125NA-DESTOCK
Only 65 units in stock Pair of suction cups. The suction cups allow you to lift a flat glass pane ready for installation safely. Simply place the suction cups on the glass and press the levers down to create a vacuum. The glass pane can now be transported safely. Please note that these suction cups have been developed for a load capacity of: 80 kg...
Reference: PSL-150-1VERIBOR
VERIBOR SUCTION CUPREF-PSL-150-1VERIBOR• Ø 150 mm : Loading capacity : 80 kg
Reference: PSL-150-1-N30
Suction cup in very good condition - Please note: sold individually Only cosmetic defects shown in the photos are present - 1 Only one item available 2nd LIFE warranty: 6 months Reinforced suction cup for windshields, sold individually Load capacity: 80 kg. High-quality handle, optimal grip on curved glass. • Sold individually • Load capacity: 80 kg. • Ø...
Reference: PSL-150-1
Suction cup deluxe sold individualy (Ø 150 mm)Easier and safer to attach that common suction lifters with clamp lever technology.The bell shaped rubber pads already adhere onto the glass surface with slight pressing even before pressing the lever.Possibility to pass a belt through. Load capacity for each lifter is 80 kg.
Reference: VP-230-E-CHARG
Charger for automated suction cup VP-230-E
Reference: VSP-290
Window holders (forside windows)Hold up the door glass while you work. Simply loop the cable over the door frame and attach the suction cups to each side of the glass.- 177 x 200 x 76 mm - 70 g
Reference: VP-230
Vacuum lifter Ø 230 mm(in a plastic case) Bell-shaped rubber pad with multiple seal lip.For optimum hold, also on strongly curved glasssurfaces.To fix with the integrated vacuum pump.Red safety ring at the pump plunger enables optical monitoring of the vacuum. Load capacity for the lifter is 120 kgDelivered in a plastic case.
Reference: VP-230SPECIALE
Vacuum lifter Ø 230 mm (in a plastic case)Bell-shaped rubber pad with multiple – seal lip. For optimum hold. To fix with the integrated vacuum pump.Red safety ring at the pump plunger enables optical monitoring of the vacuum. Load capacity for the lifter is 350 kg REF-VP-230SPECIALE•Sold individually• Load capacity around 350 kgØ 230 mmDelivered in a...
Reference: PRP21-OCCASION
OCCASION AUTOMATIC PISTON - Used for our customer demonstrations. Only one piston available Replaces the manual plunger, automatically sucks in the suction cup when the button is pressed, can be used manually if the battery is flat. 5-hour autonomy Supplied with USB-C charging cable Fits ULTRAPOSE1, ULTRAPOSE3, VP-230 and VP-230SPECIALE
Reference: DESTOCK-FRE-080-P
To prevent the corners of hubcaps from sticking out, they are often attached with adhesive tape. However, this method carries risks: adhesives can react chemically with the vehicle's paintwork, causing damage. The ideal solution? Our retaining tool, specially designed to secure hubcaps without compromising paint quality. Advantages : Optimum protection:...
Reference: 9005B
Dent suction cup. Grips very well on any surface (car body, glass, hood–).- Diameter: 115mm- Load capacity: 40kg- Sold individually
Reference: VP-205
Vacuum lifter Ø 205 mm (in a plastic case)Bell-shaped rubber pad with multiple – seal lip. For optimum hold. To fix with the integrated vacuum pump. Red safety ring at the pump plunger enables optical monitoring of the vacuum. Load capacity for the lifter is 260 kgSold individually Delivered in a case
Reference: RL-170
Suction cup with handle diameter 70 mmDurable quality suction cup. Adaptable on glass, marble, ceramic.Ideal to remove and install quarter glass.Loading capacity : 12 kgREF. RL-170Sold individually
Reference: PSL-150-1-N73
Suction cup in average condition - Please note, sold individually Cosmetic defects shown in the photos are present - Only one item available 2nd LIFE warranty: 6 months Reinforced suction cup for windshields, sold individually Load capacity: 80 kg. High-quality handle, optimal grip on curved glass. • Sold individually • Load capacity: 80 kg. • Ø 150 mm...
Reference: GEZ-543-1
Vacuum lifterØ 150 mmREPAREGLASSThese vacuum lifter have been specially designed for windsheild setting and removal.Their unique shape allows a good hand holding. The flowing shape and the smooth surface of the handles allow a greater control of large windows.To install a windshield, we ercommend beginning by doing a test. The setting of the windsheild...
Reference: KIT-VP-230-E
KIT consisting of a suction cup (REF.VP-230), 2 lithium batteries 3W- 3.7V (REF.VP-230-E-BAT) and a charger (REF.VP-230-E-CHARG). Diameter: 200mm, Flat suction cup, cannot be used on curved glass. Ideal for flat windscreens such as lorries, buses, etc. Standard suction= 160kg Maximum vertical suction = 180 kg Maximum horizontal suction= 200 kg Charger and...
Reference: NET-VENT
Rubber Cleaner is specially designed to clean and restore the appearance of all your rubber components such as seals, rubberized hubcaps, suction cups and similar surfaces. It effectively removes dirt and residues and restores the shine of rubber, prolonging its durability and appearance. Caution: This product is not recommended for certain plastics or...
Reference: VP-230-E-BATT
Battery for automated suction cup VP-230-E, with charge indicator.
Reference: PSH-125-DESTOCK
Only 65 units in stock Pair of suction cups. The suction cups allow you to lift a flat glass pane ready for installation safely. Simply place the suction cups on the glass and press the levers down to create a vacuum. The glass pane can now be transported safely. Please note that these suction cups have been developed for a load capacity of: 40 kg...
Reference: PSH-120-1-N27
Suction cup in good condition - Please note: sold individually Only cosmetic defects shown in the photos are present - 1 Only one item available 2nd LIFE warranty: 6 months The suction cup allows you to lift a window pane that is ready to be installed safely (2 are required). The edge of the window pane must not be touched after it has been prepared for...
Reference: VP-2075-DESTOCK
Sold individually - delivered in a case Suction cup with piston to create vacuum Load-bearing capacity: 200 kg Diameter: 207 mm
Reference: PE24
All you have to do to replace a manual piston is remove the manual piston and replace it with the PE24, then press the button to start the suction cup vacuum, which operates automatically. If your battery is discharged, the plunger can also be used manually. Power rating: 3.7v Charging time: 2h30 Battery life: 4 hours Supplied with USB-C charging cable...
Reference: RTD-499
Pair of ratcheting tie downsRatcheting tie downs are used by glaziers to secure freshly bonded-in glasses.Use these ratcheting tie downs together with our suction cups so as to hold vertical-glazed glasses in place while the urethane cures. The ratcheting tie downs are simply passed through the handles of the vacuum cups and tight-ened.- 165 x 165 x 10 mm...
Windshields adjustment suction cup
Stops the windshield in the correct place. ere is a simple solution to one of
the most annoying problems a technician faces today.
When a vehicle does not have stops it is difficult for one person to set the
windshield because he does not have anything to set it on.
Here is the solution, before removing the old windshield put the hood all the
way down. Set the stop on the windshield engage the vacuum and mark the
place where the stop should go.
