VBSA awarded ECOVADIS label
Banner
Recessed Cowling Clip Remover
Some self-locking cowling clips are recessed down into the cowling. They are not the type that look like a Phillips or TORX®
screw, but are the type that can be removed with a tool like the CGE-148. The only problem is the TPE657 will not reach down
into the recessed area and go under the head of the clip. If you manage to force it under the head of the clip, you can damage
the cowling around the recessed part. This is where our Recessed Cowling Clip Remover becomes the most useful tool in your
toolbox. It will fit easily down into the recessed area and then can be slid under the head of the cowling clip. You then pull up
on the center locking part and the clip can be removed.
Clip removal tool This tool is used to remove plastic clips on door linings. It fits easily down into the recessed area and then can slid under the head of the cowling clip. You then pull up on the center locking part and the clip can be removed. - 235 x 35 x 30 mm - 165 g |
Clip removal tool
€0.00 |
Recessed Cowling Clip Remover
Some self-locking cowling clips are recessed down into the cowling. They are not the type that look like a Phillips or TORX®
screw, but are the type that can be removed with a tool like the CGE-148. The only problem is the TPE657 will not reach down
into the recessed area and go under the head of the clip. If you manage to force it under the head of the clip, you can damage
the cowling around the recessed part. This is where our Recessed Cowling Clip Remover becomes the most useful tool in your
toolbox. It will fit easily down into the recessed area and then can be slid under the head of the cowling clip. You then pull up
on the center locking part and the clip can be removed.
Reference: CGE-148
Clip removal tool This tool is used to remove plastic clips on door linings. It fits easily down into the recessed area and then can slid under the head of the cowling clip. You then pull up on the center locking part and the clip can be removed. - 235 x 35 x 30 mm - 165 g
Reference: SSU-190-N48
In very good condition Only a few minor cosmetic flaws - 1 Only one item available 2nd LIFE warranty: 6 months With this sharpening stone equipped with an ergonomic handle, you can easily sharpen your worn blades while protecting your hands. Particularly recommended for restoring a precise cutting edge to cold-cutting knife blades, it is also suitable for...
Reference: TB-415
Locking strip tool With the 5 different eyelets and the pressure roller, this locking strip tool can install pratically all different types of locking strips.- 160 x Ø 25 mm - 215 g
Reference: LH-683-N144
In average condition Only a few minor cosmetic defects appear - 1 Only one item available 2nd LIFE warranty: 6 months Removing hubcaps without the right tool can quickly damage these delicate parts. If a flat screwdriver is sometimes used, its small contact surface often causes damage and does not provide sufficient leverage. The hubcap lever solves these...
Reference: DLH-511
Double-end moulding release tool This heavy-duty tool is made of steel so it will not bend. It has a small rubber spacer through each end to the tool up off the glass about 1 mm. This is important for two reasons. First, it prevents the tool from scratching the glass. Secondly, it holds the end above the glass so there is less chance the tip will catch...
Reference: CGE-148
Clip removal tool This tool is used to remove plastic clips on door linings. It fits easily down into the recessed area and then can slid under the head of the cowling clip. You then pull up on the center locking part and the clip can be removed. - 235 x 35 x 30 mm - 165 g
Reference: AST-120
Telescopic magnetWhen you work above all in the door or chassis frame of the vehicle, a screw may fall and it may be impossible to pick it up with your fingers. With this telescopic magnet, you no longer have this problem. The telescopic device is extendable from 12 (corresponding to the size of a ballpoint pen ) to 60 cm. The strong magnet is capable to...
Reference: JCS452
Compact C-clip removerC-clip removers are an item that every technician has inhis toolbox, but those C-clips removers will not alwaysfit into the tight spots and compound curves on somevehicles. The Compact C-clips remover has a flat designthat will let you use it from all sides. This handy tool isdefinitely one that no technician should be without.REF....
Reference: DESTOCK-FRE-080-P
To prevent the corners of hubcaps from sticking out, they are often attached with adhesive tape. However, this method carries risks: adhesives can react chemically with the vehicle's paintwork, causing damage. The ideal solution? Our retaining tool, specially designed to secure hubcaps without compromising paint quality. Advantages : Optimum protection:...
Reference: PRO-LAV
REF. PRO-LAVMany of the wipers system includes a glass cleaner sprayer solution.The hose is integrated to the arm wiper and runs thanks to its movements. The sprayer couldbe damaged with an arm wiper puller. The tightning nut of the puller has to be located on the specialprotector of the center area of the cleaner sprayer. Untight the bolt which is...
Reference: MK201
REF. MK-201Lockout tool setIt can easily happen that you lock yourself out, while working on customer cars. This setallows to solve this situation. Open the car door without damaging the paint, moulds andliners.. The tool kit is supplied with instruction manual.Careful, this set will not work on recent vehicles with electronically controlled locking systems
Reference: CS-696
EQUALIZER® ClipSaver door upholstery remover The front of the tool is tapered so it will fit easily under a clip. Spread the jaws slightly so they will go under and around the clip. Then, close the jaws and it removes the clip without damaging it. Great for the removal of door panels. - 230 x 76 x 51 mm - 205 g
Reference: TB-102
Rope insert tool.For the replacement of non-bonded windshields with rubber mouldings.The toll is delivered with a very resistant rope, the length of which (6 m) is enough. Can be used with private cars and trucks.
Reference: VNT-306
Urethane nozzle tool, top notchTM tool This tool allows you to cut rapidly and easily a proper V-notch on a urethane nozzle. This is important for an effective work! Indeed, before applying bond, a proper notch has to be cut. To use this tool, take a knife and cut the end of the nozzle tip to give yourself a bead. Next insert the top NotchTM tool inside...
Reference: LH-683-N113
In good condition Only a few minor cosmetic defects appear - 1 Only one item available 2nd LIFE warranty: 6 months Removing hubcaps without the right tool can quickly damage these delicate parts. If a flat screwdriver is sometimes used, its small contact surface often causes damage and does not provide sufficient leverage. The hubcap lever solves these...
Reference: CT-749
Window and doorclip removal toolThis tool is used to remove clips that are used with Opel and Ford brands, as well as with most of other vehicles that have clips.- 250 x 58 x 32 mm- 130 g
Reference: DESTOCK-MBV-SHE
REF. MBV-SHELife hammer 2 in 1This life hammer allows to break the tempered windows, its ceramic head will break the windowautomatically. Easy to use not only for adults but also for children by a secure way.This life hammer is used also to release persons from the security belt in case of automotiveaccident, thanks to its integrated blade
Reference: DPO-585
Rivet Stem Remover It is often necessary to remove dor glasses without breaking them. Drilling out the rivet so you can remove the door glass is easy if you can remove the rivet stem. Rivet stems are made of steel and are impossible to drill out. Our rivet stem remover has contoured end so it will sit over the rivet and align perfectly with the rivet...
Reference: LFA-402
flexlight mini torch with flexible shaftA screw has been lost? There is a leak in the engine compartment? A connector is hidden under the dash? This mini torch with flexible shaft will give you the needed light-in dark or hidden places. It can even become one of the most useful tools to you. Needs two LR6/AM3/AA batteries (delivered without batteries ).-...
Reference: KZS-163
Cutting nozzle tool for windshield bonding and other applications. The nozzle clamp makes it quick and easy to make an exact V-shaped cut in the nozzle tip of the polyurethane cartridge. This is important for good work! Because a bonding line must be applied with precision. Simply cut the tip of the nozzle to the required opening width.
Reference: NET-VENT
Rubber Cleaner is specially designed to clean and restore the appearance of all your rubber components such as seals, rubberized hubcaps, suction cups and similar surfaces. It effectively removes dirt and residues and restores the shine of rubber, prolonging its durability and appearance. Caution: This product is not recommended for certain plastics or...
Reference: THH-540
Telescopic bonnet holder Keeps the bonnet or hatch open at any desired angle. Telescopic bonnet holder tepless adjustable from 54 to 120 cm.
Reference: FRE-080-P-N167
In good condition Cosmetic defects shown in the photos are present - 1 Only one item available 2nd LIFE warranty: 6 months To prevent the corners of hubcaps from sticking out, they are often attached with adhesive tape. However, this method carries risks: adhesives can react chemically with the vehicle's paintwork, causing damage. The ideal solution? Our...
Reference: SSU-190-N49
In very good condition Only a few minor cosmetic flaws - 1 Only one item available 2nd LIFE warranty: 6 months With this sharpening stone equipped with an ergonomic handle, you can easily sharpen your worn blades while protecting your hands. Particularly recommended for restoring a precise cutting edge to cold-cutting knife blades, it is also suitable for...
Reference: PILE-RAPTOR522
Battery pack for RAPTOR kit Warning: these batteries are compatible with RAPTOR kits from serial number R0005372 upwards. For kits purchased before this number, you will need to order the reference PILE-RAPTORX4.
Recessed Cowling Clip Remover
Some self-locking cowling clips are recessed down into the cowling. They are not the type that look like a Phillips or TORX®
screw, but are the type that can be removed with a tool like the CGE-148. The only problem is the TPE657 will not reach down
into the recessed area and go under the head of the clip. If you manage to force it under the head of the clip, you can damage
the cowling around the recessed part. This is where our Recessed Cowling Clip Remover becomes the most useful tool in your
toolbox. It will fit easily down into the recessed area and then can be slid under the head of the cowling clip. You then pull up
on the center locking part and the clip can be removed.
