Christmas tree moulding remover

Reference: CGE-148

Clip removal tool

Clip removal tool This tool is used to remove plastic clips on door linings. It fits easily down into the recessed area and then can slid under the head of the cowling clip. You then pull up on the center locking part and the clip can be removed. - 235 x 35 x 30 mm - 165 g

Reference: LH-683-N113

Lever for hubcaps - 2nd life

In good condition Only a few minor cosmetic defects appear - 1 Only one item available 2nd LIFE warranty: 6 months Removing hubcaps without the right tool can quickly damage these delicate parts. If a flat screwdriver is sometimes used, its small contact surface often causes damage and does not provide sufficient leverage. The hubcap lever solves these...

Reference: FRE-080-P-N167

Retention device: metal strip and trim - 2nd life

In good condition Cosmetic defects shown in the photos are present - 1 Only one item available 2nd LIFE warranty: 6 months To prevent the corners of hubcaps from sticking out, they are often attached with adhesive tape. However, this method carries risks: adhesives can react chemically with the vehicle's paintwork, causing damage. The ideal solution? Our...

Reference: CTD-607

Recessed Cowling Clip Remover

Recessed Cowling Clip RemoverSome self-locking cowling clips are recessed down into the cowling. They are not the type that look like a Phillips or TORX®screw, but are the type that can be removed with a tool like the CGE-148. The only problem is the TPE657 will not reach downinto the recessed area and go under the head of the clip. If you manage to force...

Reference: DPO-585

Rivet Stem Remover

Rivet Stem Remover It is often necessary to remove dor glasses without breaking them. Drilling out the rivet so you can remove the door glass is easy if you can remove the rivet stem. Rivet stems are made of steel and are impossible to drill out. Our rivet stem remover has contoured end so it will sit over the rivet and align perfectly with the rivet...

Reference: PH-1355

Spatula curved to remove the clips

Curved Door Upholstery Remover For removing plastic fasteners in confined places. It is the same upholstery remover as the one shown above, but it is instended for use on the front part of the door where the door jam will often interfere with the removal of the door panel. Place the notch in the tool over the fastener and pry the fastener out the hole. It...

Reference: LFA-402

Flexlight bulb

flexlight mini torch with flexible shaftA screw has been lost? There is a leak in the engine compartment? A connector is hidden under the dash? This mini torch with flexible shaft will give you the needed light-in dark or hidden places. It can even become one of the most useful tools to you. Needs two LR6/AM3/AA batteries (delivered without batteries ).-...

Reference: CM-536

Magnetic bowl

Magnetic bowlThe bowl can be placed almost everywhere on a vehicule because the bottom has a rubber cover to avoid scratches. The strong magnet surely holds thebowl itself and all magnetic content.Diameter:140 mm

Reference: FRE-080-P-N153

Retention device: metal strip and trim - 2nd life

In average condition Cosmetic defects shown in the photos are present - 1 Only one item available 2nd LIFE warranty: 6 months To prevent the corners of hubcaps from sticking out, they are often attached with adhesive tape. However, this method carries risks: adhesives can react chemically with the vehicle's paintwork, causing damage. The ideal solution?...

Reference: AST-120

Telescopic magnet

Telescopic magnetWhen you work above all in the door or chassis frame of the vehicle, a screw may fall and it may be impossible to pick it up with your fingers. With this telescopic magnet, you no longer have this problem. The telescopic device is extendable from 12 (corresponding to the size of a ballpoint pen ) to 60 cm. The strong magnet is capable to...

Reference: AP-6205

Tool declipsor

Tool declipsor SPRINGERTOOL The distinct precision curvature of the Springer Clip Removal Tool provides a varaible load distribution, safely moving the load point along the tool as more leverage is applied The tapered tip allows entry under closely fitted parts and the rounded edges avoid damage to the trim or vehicle. No matter a body shop you will be...

Reference: LH-683-N55

Lever for hubcaps - 2nd life

In average condition Only a few minor cosmetic defects appear - 1 Only one item available 2nd LIFE warranty: 6 months Removing hubcaps without the right tool can quickly damage these delicate parts. If a flat screwdriver is sometimes used, its small contact surface often causes damage and does not provide sufficient leverage. The hubcap lever solves these...

Reference: SSU-190

Universal sharpening stone with handle

Reference: GRAISSE-JOINT

Rubber gasket grease - 1kg

Optimize the maintenance and durability of rubber seals with our Rubber Seal Grease - 1kg, a product specially designed for bodywork professionals and garages. Applications: Ideal for maintaining door, trunk and windshield seals. Protects seals subjected to extreme thermal variations, UV and chemical exposure. Reduces squeaking and improves joint...

Reference: CZ-444

Clip removal tool

Reference: CCR-819

EQUALIZER® cowling clip removal tool

EQUALIZER® cowling clip removal tool If expension-type cowling worked the way they were designed, you would simply unscrew the plastic screw and the clip would come out. Unfortunately, they seldom work correctly. Our cowling clip removal tool has a small sharp screw that screws into the plastic head and pulls the screw out. The clip will then collapse and...

Reference: RMI-309

Rearview Mirror Installer

Rearview Mirror Installer Use to install spring-loaded rearview mirrors with easy Spring-loaded rearview mirrors are designed to detach from the windshield when hit by the air bag.  The Rearview Mirror Mounting Tool makes the job easy and reducing the risk of breaking the windshield.  To use: Set the upper jaw against the rearview mirror, put the nylon...

Reference: PILE-RAPTORX4

Rechargeable batteries for RAPTOR Kit - Set of 4

Rechargeable batteries for RAPTOR kit - Warning note that these batteries are compatible with our RAPTOR kits with a serial number prior to R0005372. If in doubt, please contact us. Sold in packs of 4 For information: 4 batteries are required for the RAPTOR device.

Reference: SSU-190-N49

Sharpening stone with handle - 2nd life

In very good condition Only a few minor cosmetic flaws - 1 Only one item available 2nd LIFE warranty: 6 months With this sharpening stone equipped with an ergonomic handle, you can easily sharpen your worn blades while protecting your hands. Particularly recommended for restoring a precise cutting edge to cold-cutting knife blades, it is also suitable for...

Reference: FRE-080-P-N168

Retention device: metal strip and trim - 2nd life

In average condition Cosmetic defects shown in the photos are present - 1 Only one item available 2nd LIFE warranty: 6 months To prevent the corners of hubcaps from sticking out, they are often attached with adhesive tape. However, this method carries risks: adhesives can react chemically with the vehicle's paintwork, causing damage. The ideal solution?...

Reference: KZS-163

KZS-163 cutting nozzle tools for windshield bonding or other applications

Cutting nozzle tool for windshield bonding and other applications. The nozzle clamp makes it quick and easy to make an exact V-shaped cut in the nozzle tip of the polyurethane cartridge. This is important for good work! Because a bonding line must be applied with precision. Simply cut the tip of the nozzle to the required opening width.

Reference: LT-415-1

5 adaptable eylets

5 replacement eylets

Reference: THH-540

Telescopic bonnet holder

Telescopic bonnet holder Keeps the bonnet or hatch open at any desired angle. Telescopic bonnet holder tepless adjustable from 54 to 120 cm.

Reference: TENDEURCAMERA

CAMERA/RETRO SUPPORT

Reference: BMR-1488

Lever for side window seals

Lever to unclip the side window frame for easy removal

Reference: TB-415

Locking strip tool with 5 interchangeable eyelets

Locking strip tool With the 5 different eyelets and the pressure roller, this locking strip tool can install pratically all different types of locking strips.- 160 x Ø 25 mm - 215 g

Reference: DESTOCK-PS-215

Glue joint smoother/extractor

Simplify your finishing and joint removal jobs with this versatile tool designed for professionals. Key features: Dual function: Allows you to even out glue joints for a perfect finish and easily remove joints (silicone, PU). Convenient use: work is performed with one hand, saving time and facilitating handling. Precision and cleanliness: Guarantees...

Reference: TB-102

Rope insert tool length of the rope: 9m (pour bus et poids lourds)

Rope insert tool.For the replacement of non-bonded windshields with rubber mouldings.The toll is delivered with a very resistant rope, the length of which (6 m) is enough. Can be used with private cars and trucks.

Reference: CS-696

Clipsaver door upholstery remover

EQUALIZER® ClipSaver door upholstery remover The front of the tool is tapered so it will fit easily under a clip. Spread the jaws slightly so they will go under and around the clip. Then, close the jaws and it removes the clip without damaging it. Great for the removal of door panels. - 230 x 76 x 51 mm - 205 g

Reference: LH-683-N144

Lever for hubcaps - 2nd life

In average condition Only a few minor cosmetic defects appear - 1 Only one item available 2nd LIFE warranty: 6 months Removing hubcaps without the right tool can quickly damage these delicate parts. If a flat screwdriver is sometimes used, its small contact surface often causes damage and does not provide sufficient leverage. The hubcap lever solves these...