VBSA awarded ECOVADIS label
Banner
Also note that this drawer is in selection for the "Servante à la carte" (custom design) formula
Reference: SERV-OPB-NUE
Compose your workshop trolley which corresponds to your needs & which looks like you ! It is made for you... It is made by you ! Please note: You have 5 small drawers and 2 large drawers, think about it during your design.
Reference: AIG-125
Just lay the wire in the notched tip and pass it through the polyurethane by pushing the tool from the inside to the outside.In the way, you can release the window. Always place the flat surface of the wire threader on the window, so that the hollow tube is not deformed.- 120 x 26 x 10 mm - 20 g
Reference: DPO-585
Rivet Stem Remover It is often necessary to remove dor glasses without breaking them. Drilling out the rivet so you can remove the door glass is easy if you can remove the rivet stem. Rivet stems are made of steel and are impossible to drill out. Our rivet stem remover has contoured end so it will sit over the rivet and align perfectly with the rivet...
Reference: WFA-500
REF. WFA-500Arm Wiper pullerArm wiper puller especially designed forVolkswagen rear window models, Audi, Skoda,Seat, but also many others.Untight the button from the arm but do not release it( could caused damages on the plasticcompartments of the arm.) Position the jaw on thearm of the wiper, tight manually first, then use aratchet 3/8 to strongly tight...
Reference: pistolet-manuel
The VBSA manual glue gun is an essential tool for the precise and consistent application of glue in cartridges or sticks. Robust and easy to use, it is ideal for professional use in glazing, automotive, and construction applications. Two models are available to suit your needs: V80: compatible with 310 ml and 400 ml cartridges V81: compatible with 400 ml...
Reference: 601M
Effectively protect vehicle interiors with this special glass breakage film. Key features: Optimum protection: Prevents water and dust from entering the vehicle before replacing broken or damaged glass. Special glass breakage film: Ideal for maintaining temporary protection while ensuring the safety of occupants and interior equipment. Lightly adhesive:...
Reference: JP135-N263
Suction cup in very good condition Only cosmetic defects shown in the photos are present - 1 Only one available 2nd LIFE warranty: 6 months Automatic vacuum suction cup - Load capacity 45kg - Diameter 175mm
Reference: 8PD015265-841-N2939
Not avalaible
Reference: NSE-MOUSSE132
The protective foam for NSE-B160 and NSE-B101 extendable tie-down bars is designed to effectively protect surfaces and equipment during securing and transport operations. It limits the risk of scratches, impacts, or marks on items in contact with the tie-down bars.Measuring 132 cm in length, this foam fits perfectly on compatible bars to provide optimal...
Reference: L2
Olfa®knife This knife is made of high impact plastic, has a stainless steel blade housing and a positive locking thumb wheel so that you can set the blade at any length. The back of the knife features a rubber grip that lets the knife rest comfortably in your hand and keeps it from slipping. The famous model. - 146 x 40 x 20 mm - 110 g
Reference: VP-230SPECIALE-N337
In good condition Only cosmetic defects shown in the photos are present - 1 Only one item available 2nd LIFE warranty: 6 months Ø 230 mm Piston Suction Cup – For Heavy Loads and Curved Glass Surfaces Designed for handling very heavy loads up to 350 kg, this professional Ø 230 mm suction cup is ideal for working with highly curved glass, such as bus...
Reference: CAISSE-N436
In very good condition There are only a few minor cosmetic flaws—only 1 item available 2nde VIE warranty: 6 months Storage case Dimensions: 310MM x 170 x 135H
Reference: FSC1.7POIGNEE
Highly recommended for optimal handling and better cutting control, this handle improves the precision and stability of the tool, especially during complex or prolonged cutting tasks. An essential accessory for getting the most out of your FEIN cordless knife.
Reference: GRAISSE-JOINT
Optimize the maintenance and durability of rubber seals with our Rubber Seal Grease - 1kg, a product specially designed for bodywork professionals and garages. Applications: Ideal for maintaining door, trunk and windshield seals. Protects seals subjected to extreme thermal variations, UV and chemical exposure. Reduces squeaking and improves joint...
Reference: KIT-AGRAFES-ECO24
SET OF WINDSHIELD CLIPS AND STAPLES Contains the 32 most frequently used references Box size: L: 46.5cm x W: 38cm x H: 7cm See all clips in the page description
Reference: EHL-652
These latex gloves, lightly powdered, offer excellent protection and hygiene while guaranteeing good dexterity. Ideal for handling delicate surfaces, they allow you to touch the edge of the glass without risk of contamination. Characteristics: Material: Natural latex, lightly powdered for easy donning Single use, non-sterile Comfort and flexibility:...
Reference: 848031AIGUILLE
Needle to guide the wire upper the metal tabs from the car .
Reference: SC313
12 mm scraper blades for ref. FSC-300SPECIAL- Package of 10 blades- 65 x 20 x 70 mm - 26 g
Reference: VNT-306
This cutter is specially designed to precisely cut the nozzle of polyurethane cartridges used for installing windshields. It quickly creates a perfectly even V-shaped notch, which is essential for applying a clean and uniform bead of adhesive. It is easy to use: first cut the end of the nozzle to the desired width, then insert the pliers into the opening...
Reference: V54-N525
General condition: No issues, Good condition Only the cosmetic defects shown in the photos are present - Only one unit available 2nde VIE Warranty: 6 months Designed for extruding standard 310 ml cartridges and 400 ml cartridges, it ensures smooth, controlled and effortless application. Main features: Compatible with 310 ml cartridges and 400 ml...
Reference: VB89427
Sold in packs of 10 Type: Panel stop - Ring Color: Natural Material: Nylon Polyamide PA6
Reference: 8PZ010611-931-DESTOCKAGE
Please note: Only 1 target available CSC TOOL - HYUNDAI 1-20
Reference: PWR-2016-112
Circular washer specially designed for fitting cartridges to MILWAUKEE 12V guns. It guarantees optimum cartridge retention in the cylinder, ensuring stable, even extrusion. An essential accessory for precise, efficient use of your Milwaukee gun.
Reference: NSE-828
Delivered without castors
Also note that this drawer is in selection for the "Servante à la carte" (custom design) formula
