Reference: 9005B
Dent suction cup
Dent suction cup. Grips very well on any surface (car body, glass, hood–).- Diameter: 115mm- Load capacity: 40kg- Sold individually
Moulding hold down tool
The corners on mouldings will often raise up and leave an unsightly gap under them.
Taping these mouldings down can be disastrous because the tape will sometimes attack then paint and, in the worst case, remove it.
This moulding hold down tool is attached with a vaccum cup.
Pressure is then applied to each end of the tool by tightening the adjustable wing nut and applying upward pressure on the vaccum cup, thereby applying downward pressure on both ends.
- 182 x 80 x 80 mm
- 75 g
- Sold individually
Secure payment
FREE SHIPPING from 150,00 € H.T. (France métropolitaine)
Certified organization
Moulding hold down tool
The corners on mouldings will often raise up and leave an unsightly gap under them.
Taping these mouldings down can be disastrous because the tape will sometimes attack then paint and, in the worst case, remove it.
This moulding hold down tool is attached with a vaccum cup.
Pressure is then applied to each end of the tool by tightening the adjustable wing nut and applying upward pressure on the vaccum cup, thereby applying downward pressure on both ends.
- 182 x 80 x 80 mm
- 75 g
- Sold individually
Reference: 9005B
Dent suction cup. Grips very well on any surface (car body, glass, hood–).- Diameter: 115mm- Load capacity: 40kg- Sold individually
Reference: JP135
JetPacks'" EQUALIZER vacuum cups were designed from the ground-up to eliminate the need for manual pumping. Turn on theJetPacks'", place them on the glass and let them handle the pumping. If the cup loses vacuum, AIR FORCE'" vacuum technology takes over and keeps that crucial suction going until the cup has maximum vacuum again. JetPacks™ has a 175mm...
Reference: VP-230
Vacuum lifter Ø 230 mm(in a plastic case) Bell-shaped rubber pad with multiple seal lip.For optimum hold, also on strongly curved glasssurfaces.To fix with the integrated vacuum pump.Red safety ring at the pump plunger enables optical monitoring of the vacuum. Load capacity for the lifter is 120 kgDelivered in a plastic case.
Reference: VP-2075
Sold individually - delivered in a case
Reference: PSL-150-1VERIBOR
VERIBOR SUCTION CUPREF-PSL-150-1VERIBOR• Ø 150 mm : Loading capacity : 80 kg
Reference: PSL-150-1
Suction cup deluxe sold individualy (Ø 150 mm)Easier and safer to attach that common suction lifters with clamp lever technology.The bell shaped rubber pads already adhere onto the glass surface with slight pressing even before pressing the lever.Possibility to pass a belt through. Load capacity for each lifter is 80 kg.
Reference: VP-205
Vacuum lifter Ø 205 mm (in a plastic case)Bell-shaped rubber pad with multiple – seal lip. For optimum hold. To fix with the integrated vacuum pump. Red safety ring at the pump plunger enables optical monitoring of the vacuum. Load capacity for the lifter is 260 kgSold individually Delivered in a case
Reference: GEZ-543-1
Vacuum lifterØ 150 mmREPAREGLASSThese vacuum lifter have been specially designed for windsheild setting and removal.Their unique shape allows a good hand holding. The flowing shape and the smooth surface of the handles allow a greater control of large windows.To install a windshield, we ercommend beginning by doing a test. The setting of the windsheild...
Reference: PSH-120
Pairof suction cups (Ø 120 mm)Vacuum cups allow you to hold safely a window that is ready to install. The edge of the window must not be touched once the window is ready for the installation. Each vacuum swivels up and down approximately 30° to fit radically contoured glass. Simply set the vacuum cups in place and push the thumb latches down to engage the...
Reference: PSH-120-VERIBOR
VERIBOR SUCTION CUP PAIR.REF. PSH-120-VERIBOR• Ø 120 mm : Loading capacity : 80 kg
Reference: VP-230SPECIALE
Vacuum lifter Ø 230 mm (in a plastic case)Bell-shaped rubber pad with multiple – seal lip. For optimum hold. To fix with the integrated vacuum pump.Red safety ring at the pump plunger enables optical monitoring of the vacuum. Load capacity for the lifter is 350 kg REF-VP-230SPECIALE•Sold individually• Load capacity around 350 kgØ 230 mmDelivered in a...
Reference: RTD-499
Pair of ratcheting tie downsRatcheting tie downs are used by glaziers to secure freshly bonded-in glasses.Use these ratcheting tie downs together with our suction cups so as to hold vertical-glazed glasses in place while the urethane cures. The ratcheting tie downs are simply passed through the handles of the vacuum cups and tight-ened.- 165 x 165 x 10 mm...
Reference: RL-170
Suction cup with handle diameter 70 mmDurable quality suction cup. Adaptable on glass, marble, ceramic.Ideal to remove and install quarter glass.Loading capacity : 12 kgREF. RL-170Sold individually