U shape 19 mm Equalizer cutting blade

Reference: Z6

Cold knife blade, extra fine 38 mm

Cold knife blade, extra fine - Sold individually - Cutting length: 38 mm - 20 g CARTON OF 10

More

Reference: FB073

FEIN cutting blade, straight 35 mm

FEIN cutting blade, straight 35 mm (56 mm 12 g)

More

Reference: FB212

Serrated hook blade with U shape - 36 mm

Lame à crochet crantéeprofondeur de coupe : 36 mmvendue à l'unité

More

Reference: WK3

Multi-purpose, bent BTB blade, 200mm

Lame BTB multi-fonction plate 200mm(utilisation générale)

More

Reference: BOB-1.5-ROLL-OUT

Round wire in a spool REPAREGLASS - ø 0,80 mm, 1500 ml

Round wire in a spool The round profile and the small diameter make this wire a real problem solver for todays cars with narrow gaps between glass and body. It has the same high tensile strength than the VKD-44but offers at the same time as much lower risk to damage interior linings and dashboards.679 Newtonø 0,80 mm, 1500 ml

More

Reference: DLH-511

Double-end moulding release tool

Double-end moulding release tool This heavy-duty tool is made of steel so it will not bend. It has a small rubber spacer through each end to the tool up off the glass about 1 mm. This is important for two reasons. First, it prevents the tool from scratching the glass. Secondly, it holds the end above the glass so there is less chance the tip will catch...

More

Reference: VNT-306

EQUALIZER® top notchtm tool

Urethane nozzle tool, top notchTM tool This tool allows you to cut rapidly and easily a proper V-notch on a urethane nozzle. This is important for an effective work! Indeed, before applying bond, a proper notch has to be cut. To use this tool, take a knife and cut the end of the nozzle tip to give yourself a bead. Next insert the top NotchTM tool inside...

More

Reference: ZK45

ZipKnife™ COLD KNIFE

The compact ZIPKNIFE cold knife is designed for cutting in hard-to-reach areas. Uses all standard cold knife blades Without blade.

More

Reference: HDW5634FEUTRE

Felt for RAPTOR device

Felt for RAPTOR device

More

Reference: ENO841

Cutting blade. Length: 25mm

Cutting blade. Length: 25mm - 60 x 30 x 25 mm 45 gBE CAREFUL: Ninja blades have been elaborated to fit on the Ninja knife. They should not be used with other knives.

More

Reference: TE-125

Torx t80 for arms of windshield pullers

This very wide piece is recommended for windshield removal on the BMW 5 and BMW 7 series.- 35 x 18 x 18 mm - 38 g

More

Reference: WFA-525

Arm wiper puller for rearwindows.

Arm wiper puller for rearwindows.To avoid to damage the arm wipersfrom rear vehicules, which are oftendamage with traditional arm wiper pullersEx: Peugeot 307-207, Renaultclio III, Espace Laguna, Megane,Nissan Micra et primera

More

Reference: FB099

Cutting blade, cranked -19mm

Cutting blade, crankedCutting length: 19 mmSold individually

More

Reference: SD-21

Braided wire - ø 0,80 mm - 22.5M

Braided wire21 ml REPAREGLASSBraided wire The braided wire is made of three stainless steel resistant wires that are braided to one strand. The wire is anodized (with a traditional gold colour). It has a 0.80mm diameter.

More

Reference: SK130

Replacement blade for fsl 240 pinchweld scraper l:16mm

Replacement blade for fsl 240 pinchweld scraper l:16mm

More

Reference: PAIG-200

Wire gripping handles (corkscrew shape)

Wire gripping handlesIdeal solution to work rapidly and without problem. Feed the wire through the hole in the wedge shaft (fig A), loop it through the hole at the top of the shaft (fig B) and then bring it back into the large plastic handle. By pressing the wedge back into the handle, the wire is held in place (fig C). To shorten the wire, press down on...

More