VBSA awarded ECOVADIS label
Banner
Everyprotector they used could not withstand repeated hits by a power tool blade and would jump out of the pinchweld,
leaving the paint exposed to potential harm. Tape worked to some extent, but would not hold sufficient downward pressure to
keep the pinchweld protector in place.
This kit includes 4 different lengths of a high impact metal that will absorb repeated striking from the blade, and uses a vacuum
hold down tool to exert pressure to keep the pinchweld protector in place.
There are many places where this will be useful, but most important are the new vehicles that have no moulding around the glass.
Even a small nick on those vehicles is easy to see from outside and can result in the need to have that part of the vehicle repainted.
REF-MLP-182 • Pinchweld protector 120 cm
REF-MTF-183 • Pinchweld protector 60 cm
REF-MET-184 • Pinchweld protector 40 cm
REF-MTI-185 • Pinchweld protector 30 cm
REF-FRE-080-P • Moulding hold down tool - Sold individually
Secure payment
FREE SHIPPING from 150,00 € H.T. (France métropolitaine)
Certified organization
Sold individually Moulding hold down tool To prevent the corners of wheel trims from sticking out, they are often fixed with adhesive tape. But this can react chemically with the vehicle's paintwork and damage it. The solution is offered by our retaining tool, which is fixed to the bodywork with an integrated suction cup and holds the hubcap in place with plastic arms.The pressure to be applied is adjusted with a wing nut. |
Moulding hold down tool
€0.00 |
Everyprotector they used could not withstand repeated hits by a power tool blade and would jump out of the pinchweld,
leaving the paint exposed to potential harm. Tape worked to some extent, but would not hold sufficient downward pressure to
keep the pinchweld protector in place.
This kit includes 4 different lengths of a high impact metal that will absorb repeated striking from the blade, and uses a vacuum
hold down tool to exert pressure to keep the pinchweld protector in place.
There are many places where this will be useful, but most important are the new vehicles that have no moulding around the glass.
Even a small nick on those vehicles is easy to see from outside and can result in the need to have that part of the vehicle repainted.
REF-MLP-182 • Pinchweld protector 120 cm
REF-MTF-183 • Pinchweld protector 60 cm
REF-MET-184 • Pinchweld protector 40 cm
REF-MTI-185 • Pinchweld protector 30 cm
REF-FRE-080-P • Moulding hold down tool - Sold individually
Reference: DESTOCK-FRE-080-P
Sold individually Moulding hold down tool To prevent the corners of wheel trims from sticking out, they are often fixed with adhesive tape. But this can react chemically with the vehicle's paintwork and damage it. The solution is offered by our retaining tool, which is fixed to the bodywork with an integrated suction cup and holds the hubcap in place with...
Reference: ZK45
The compact ZIPKNIFE cold knife is designed for cutting in hard-to-reach areas. Uses all standard cold knife blades Without blade.
Reference: WK2S
Serrated, average, universal, flat BTB blade, 240mm
Reference: FB143
lame à découper avec roulette de butée 16-35 mm
Reference: WK4Z
Deep offset, multi-purpose BTB blade, 140mm
Reference: ROLL-N-CUT
A simply system to cut-out windshieds with wrenches. This system is exceptional in that it is designed to be used with a single suction cup, which is easy to move thanks to the regulator attached to the unit. The box includes a metal protection strip and polyethylene protectors. A suction-cup-mounted piano wire reel is also supplied, which is positioned...
Reference: EEB793
EQUALIZER® blades and sheathsEQUALIZER® blade 100mmThe blade is made of unbreakable mild steel.In case the blade bends,use pliers to straighten it up. Use a bech grinder, a strip sander, a file or a whetstone. You do not need to remove the blade to sharpen it. Our blades are made of specific material.Their round edges prevent them from being bent inside...
Reference: FB110
REF-FB-110 Lame à crochet en U Profondeur de coupe 40 mmvendue à l’unité
Reference: CS-696
EQUALIZER® ClipSaver door upholstery remover The front of the tool is tapered so it will fit easily under a clip. Spread the jaws slightly so they will go under and around the clip. Then, close the jaws and it removes the clip without damaging it. Great for the removal of door panels. - 230 x 76 x 51 mm - 205 g
Reference: WFA-500
REF. WFA-500Arm Wiper pullerArm wiper puller especially designed forVolkswagen rear window models, Audi, Skoda,Seat, but also many others.Untight the button from the arm but do not release it( could caused damages on the plasticcompartments of the arm.) Position the jaw on thearm of the wiper, tight manually first, then use aratchet 3/8 to strongly tight...
Reference: SD-22
Braided wire in a spool REPAREGLASS ø 0.80 mm, length: 22 m, Wound on a plastic spool. 1083 NEWTON The wire to be cut is twisted according to our exact specifications from three strong stainless steel wires. The wire is anodised in a typical "gold" colour.
Reference: AP-6205
Tool declipsor SPRINGERTOOL The distinct precision curvature of the Springer Clip Removal Tool provides a varaible load distribution, safely moving the load point along the tool as more leverage is applied The tapered tip allows entry under closely fitted parts and the rounded edges avoid damage to the trim or vehicle. No matter a body shop you will be...
Reference: WFA-525
Arm wiper puller for rearwindows.To avoid to damage the arm wipersfrom rear vehicules, which are oftendamage with traditional arm wiper pullersEx: Peugeot 307-207, Renaultclio III, Espace Laguna, Megane,Nissan Micra et primera
Reference: DESTOCK-WK7
Single handle for BTB blade - Makes it easy to cut windshield and other glazing seals. Dimensions: 100 x 38 x 38 mm
Everyprotector they used could not withstand repeated hits by a power tool blade and would jump out of the pinchweld,
leaving the paint exposed to potential harm. Tape worked to some extent, but would not hold sufficient downward pressure to
keep the pinchweld protector in place.
This kit includes 4 different lengths of a high impact metal that will absorb repeated striking from the blade, and uses a vacuum
hold down tool to exert pressure to keep the pinchweld protector in place.
There are many places where this will be useful, but most important are the new vehicles that have no moulding around the glass.
Even a small nick on those vehicles is easy to see from outside and can result in the need to have that part of the vehicle repainted.
REF-MLP-182 • Pinchweld protector 120 cm
REF-MTF-183 • Pinchweld protector 60 cm
REF-MET-184 • Pinchweld protector 40 cm
REF-MTI-185 • Pinchweld protector 30 cm
REF-FRE-080-P • Moulding hold down tool - Sold individually
