VBSA awarded ECOVADIS label
Banner
Curved wire threader:
The curved wire threader anables threading of the cutting wire even
where the gap between glass and pinch weld is very small.
This is especially helpful on side and back windows where conventional
wire threaders are often difficult to use.
The curved threader can be pushed through the adhesive bead from inside
to outside or from outside to inside.Piercing works best with the aid of
long-nosed pliers.
REF. DST-53
Curved wire threader 53 mm (package at 3 pièces)
REF. DST-58
Curved wire threader 58 mm (package at 3 pièces)
REF. DST-61
Curved wire threader 61 mm (package at 3 pièces)
Curved wire threader:
The curved wire threader anables threading of the cutting wire even
where the gap between glass and pinch weld is very small.
This is especially helpful on side and back windows where conventional
wire threaders are often difficult to use.
The curved threader can be pushed through the adhesive bead from inside
to outside or from outside to inside.Piercing works best with the aid of
long-nosed pliers.
REF. DST-53
Curved wire threader 53 mm (package at 3 pièces)
REF. DST-58
Curved wire threader 58 mm (package at 3 pièces)
REF. DST-61
Curved wire threader 61 mm (package at 3 pièces)
Reference: XKD-44A
Discover our new REF-XKD-44 square piano wire, designed to offer exceptional strength and meet the most demanding needs. Applications: Used for precise cutting of windscreens and automotive glazing, this rope is a must-have for bodybuilders and garages. Its sturdy, square design ensures a firm grip and greater efficiency when removing glass and similar...
Reference: CAISSE-N395
In very good condition Only a few minor cosmetic flaws - 1 Only one item available 2nd LIFE warranty: 6 months Storage case Length: 44cm - Width: 17cm - Height: 19cm
Reference: BAT-FSC1.7
This 18 V - 2.4 Ah Li-ion battery is specially designed to power FEIN battery-powered knives of previous generations. Offering reliable and consistent performance, it is ideal for extending the life of your compatible FEIN tools. Key features: Li-ion technology: Ensures stable autonomy and fast recharging. 2.4 Ah capacity: Optimized for work requiring...
Reference: PAIG-200
Wire gripping handlesIdeal solution to work rapidly and without problem. Feed the wire through the hole in the wedge shaft (fig A), loop it through the hole at the top of the shaft (fig B) and then bring it back into the large plastic handle. By pressing the wedge back into the handle, the wire is held in place (fig C). To shorten the wire, press down on...
Reference: FB076
cutting length: 24mm 17g Sold individually
Reference: LH-683-N144
In average condition Only a few minor cosmetic defects appear - 1 Only one item available 2nd LIFE warranty: 6 months Removing hubcaps without the right tool can quickly damage these delicate parts. If a flat screwdriver is sometimes used, its small contact surface often causes damage and does not provide sufficient leverage. The hubcap lever solves these...
Reference: AP-6205
Tool declipsor SPRINGERTOOL The distinct precision curvature of the Springer Clip Removal Tool provides a varaible load distribution, safely moving the load point along the tool as more leverage is applied The tapered tip allows entry under closely fitted parts and the rounded edges avoid damage to the trim or vehicle. No matter a body shop you will be...
Reference: EWA-1702
Extremely loadable. Made of massive metal. Can be used on virtually any passenger and commercial vehicle. Specially recommended for the BMW 5 and BMW 7 series.- 104 x 38 x 140 mm- 518 g
Reference: 848031AIGUILLE
Needle to guide the wire upper the metal tabs from the car .
Reference: HB10
Heavy-duty snap-off blade- package of 10 pieces- 140 x 25 x 0.7 mm - 106 g
Reference: DLH-511
Double-end moulding release tool This heavy-duty tool is made of steel so it will not bend. It has a small rubber spacer through each end to the tool up off the glass about 1 mm. This is important for two reasons. First, it prevents the tool from scratching the glass. Secondly, it holds the end above the glass so there is less chance the tip will catch...
Reference: CGE-148
Clip removal tool This tool is used to remove plastic clips on door linings. It fits easily down into the recessed area and then can slid under the head of the cowling clip. You then pull up on the center locking part and the clip can be removed. - 235 x 35 x 30 mm - 165 g
Reference: AIG-300
The wire guide's long, narrow shaft allows positioning the wire so it prevents the dash and interior mouldings from being damaged. Recommended above all for cars with a high windshield slope or with a bottom window bond that is hardly accessible. Of course, the wire guide can also be used from the outside.- 350 x 38 x 38 mm - 220 g
Reference: TKS-100
Trapezoid blades. In a pratical dispenser. Our replacement blades for utility knives are 0,6 mm thick, so they are very sturdy. These blades are in a safety dispenser with a suspension hook so as to avoid any risk of injury. You take new blades by sliding them out from the above side of the dispenser while youdispose of the worn out blades by sliding them...
Reference: FB101
REF-FB-101 Hook blade with U shapeCutting length: 60 mmSold individually
Reference: MRL6
This scraper can be carried in the pocket - no risk of injury.The replacement of the blade is easy and secure. When not in use, the blade is simply flipped so as to avoid any injury. When you want to use the scraper, pull the closing device, flip the blade and your scraper is ready to use!1 Package of 6 pieces.- 50 x 44 x 38 mm - 45 g
Reference: SD-22
Braided wire in a spool REPAREGLASS ø 0.80 mm, length: 22 m, Wound on a plastic spool. 1083 NEWTON The wire to be cut is twisted according to our exact specifications from three strong stainless steel wires. The wire is anodised in a typical "gold" colour.
Reference: RR23-CLIQUETRAPTOR
Please note that this ratchet is not compatible with the RAPTOR Kit. 1 Ratchet For ROLL-N-CUT kit
Reference: BOB-1.5-ROLL-OUT
Round wire in a spool The round profile and the small diameter make this wire a real problem solver for todays cars with narrow gaps between glass and body. It has the same high tensile strength than the VKD-44but offers at the same time as much lower risk to damage interior linings and dashboards.679 Newtonø 0,80 mm, 1500 ml
Reference: PSD6
Parer blades (scraper not include)REF-PSD-6 Blade diameter 6 mmThese parer blades are especially good for cleaning the pinchweldfrom excessively applied polyurethane in curves and corners.Thereby the special shape reduces the risk of damaging the paintcompared to standard scraper blades. The blades are suitable for ourscraper tools FSC-300SPECIAL and...
Reference: 3008-K
The new REPAREGLASS cold knife offers an optimized grip thanks to a handle grip inspired by standard cold knives, for enhanced comfort of use. Lighter, thinner, and smoother than the 3007-K model, it ensures excellent maneuverability during cutting. The blades are adjustable, allowing you to set the depth according to your needs for precise work. Easy...
Reference: Z9
Cold knife blade coated, extra fine - Sold individually- Cutting length: 38 mm- 20gCARTON OF 10
Curved wire threader:
The curved wire threader anables threading of the cutting wire even
where the gap between glass and pinch weld is very small.
This is especially helpful on side and back windows where conventional
wire threaders are often difficult to use.
The curved threader can be pushed through the adhesive bead from inside
to outside or from outside to inside.Piercing works best with the aid of
long-nosed pliers.
REF. DST-53
Curved wire threader 53 mm (package at 3 pièces)
REF. DST-58
Curved wire threader 58 mm (package at 3 pièces)
REF. DST-61
Curved wire threader 61 mm (package at 3 pièces)
