Lever for hubcaps - 2nd life

Reference: LT-415-1

5 adaptable eylets

5 replacement eylets

Reference: MK201

Lockout tool set

REF. MK-201Lockout tool setIt can easily happen that you lock yourself out, while working on customer cars. This setallows to solve this situation. Open the car door without damaging the paint, moulds andliners.. The tool kit is supplied with instruction manual.Careful, this set will not work on recent vehicles with electronically controlled locking systems

Reference: TENDEURCAMERA

CAMERA/RETRO SUPPORT

Reference: TB-415

Locking strip tool with 5 interchangeable eyelets

Locking strip tool With the 5 different eyelets and the pressure roller, this locking strip tool can install pratically all different types of locking strips.- 160 x Ø 25 mm - 215 g

Reference: FRE-080-P-N167

Retention device: metal strip and trim - 2nd life

In good condition Cosmetic defects shown in the photos are present - 1 Only one item available 2nd LIFE warranty: 6 months To prevent the corners of hubcaps from sticking out, they are often attached with adhesive tape. However, this method carries risks: adhesives can react chemically with the vehicle's paintwork, causing damage. The ideal solution? Our...

Reference: LH-683-N55

Lever for hubcaps - 2nd life

In average condition Only a few minor cosmetic defects appear - 1 Only one item available 2nd LIFE warranty: 6 months Removing hubcaps without the right tool can quickly damage these delicate parts. If a flat screwdriver is sometimes used, its small contact surface often causes damage and does not provide sufficient leverage. The hubcap lever solves these...

Reference: PILE-RAPTORX4

Rechargeable batteries for RAPTOR Kit - Set of 4

Rechargeable batteries for RAPTOR kit - Warning note that these batteries are compatible with our RAPTOR kits with a serial number prior to R0005372. If in doubt, please contact us. Sold in packs of 4 For information: 4 batteries are required for the RAPTOR device.

Reference: PH-1355

Spatula curved to remove the clips

Curved Door Upholstery Remover For removing plastic fasteners in confined places. It is the same upholstery remover as the one shown above, but it is instended for use on the front part of the door where the door jam will often interfere with the removal of the door panel. Place the notch in the tool over the fastener and pry the fastener out the hole. It...

Reference: LFA-402

Flexlight bulb

flexlight mini torch with flexible shaftA screw has been lost? There is a leak in the engine compartment? A connector is hidden under the dash? This mini torch with flexible shaft will give you the needed light-in dark or hidden places. It can even become one of the most useful tools to you. Needs two LR6/AM3/AA batteries (delivered without batteries ).-...

Reference: RMI-309

Rearview Mirror Installer

Rearview Mirror Installer Use to install spring-loaded rearview mirrors with easy Spring-loaded rearview mirrors are designed to detach from the windshield when hit by the air bag.  The Rearview Mirror Mounting Tool makes the job easy and reducing the risk of breaking the windshield.  To use: Set the upper jaw against the rearview mirror, put the nylon...

Reference: CZ-444

Clip removal tool

Reference: CS-696

Clipsaver door upholstery remover

EQUALIZER® ClipSaver door upholstery remover The front of the tool is tapered so it will fit easily under a clip. Spread the jaws slightly so they will go under and around the clip. Then, close the jaws and it removes the clip without damaging it. Great for the removal of door panels. - 230 x 76 x 51 mm - 205 g

Reference: SSU-190

Universal sharpening stone with handle

Reference: CTD-607

Recessed Cowling Clip Remover

Recessed Cowling Clip RemoverSome self-locking cowling clips are recessed down into the cowling. They are not the type that look like a Phillips or TORX®screw, but are the type that can be removed with a tool like the CGE-148. The only problem is the TPE657 will not reach downinto the recessed area and go under the head of the clip. If you manage to force...

Reference: KZS-163

KZS-163 cutting nozzle tools for windshield bonding or other applications

Cutting nozzle tool for windshield bonding and other applications. The nozzle clamp makes it quick and easy to make an exact V-shaped cut in the nozzle tip of the polyurethane cartridge. This is important for good work! Because a bonding line must be applied with precision. Simply cut the tip of the nozzle to the required opening width.

Reference: LH-683-N113

Lever for hubcaps - 2nd life

In good condition Only a few minor cosmetic defects appear - 1 Only one item available 2nd LIFE warranty: 6 months Removing hubcaps without the right tool can quickly damage these delicate parts. If a flat screwdriver is sometimes used, its small contact surface often causes damage and does not provide sufficient leverage. The hubcap lever solves these...

Reference: FRE-080-P-N153

Retention device: metal strip and trim - 2nd life

In average condition Cosmetic defects shown in the photos are present - 1 Only one item available 2nd LIFE warranty: 6 months To prevent the corners of hubcaps from sticking out, they are often attached with adhesive tape. However, this method carries risks: adhesives can react chemically with the vehicle's paintwork, causing damage. The ideal solution?...

Reference: SSU-190-N49

Sharpening stone with handle - 2nd life

In very good condition Only a few minor cosmetic flaws - 1 Only one item available 2nd LIFE warranty: 6 months With this sharpening stone equipped with an ergonomic handle, you can easily sharpen your worn blades while protecting your hands. Particularly recommended for restoring a precise cutting edge to cold-cutting knife blades, it is also suitable for...

Reference: 252

Water-repellent white grease aerosol - 400ml

A high-performance lubricant to protect and maintain your moving parts. Key features: Thixotropic formula: Ideal for parts subjected to high pressure, shock and oscillation. Provides long-lasting lubrication even under extreme conditions. Excellent adhesion: Stays in place on all surfaces, even during continuous movement. Water- and corrosion-repellent:...

Reference: PILE-RAPTOR522

Battery pack for RAPTOR Kit

Battery pack for RAPTOR kit Warning: these batteries are compatible with RAPTOR kits from serial number R0005372 upwards. For kits purchased before this number, you will need to order the reference PILE-RAPTORX4.

Reference: CT-749

Window and door clip removal tool

Window and doorclip removal toolThis tool is used to remove clips that are used with Opel and Ford brands, as well as with most of other vehicles that have clips.- 250 x 58 x 32 mm- 130 g

Reference: NMT-448

Mechanical pick up

Mechanical pick up The use of telescopic magnet could be sometimes impossible to use because of non ferrous items. It is times like these when you need our Mechanical Pick-Up. It is designed with steel fingers that are spring-loaded that will grip an item up to 2,5 cm in diameter.

Reference: CCR-819

EQUALIZER® cowling clip removal tool

EQUALIZER® cowling clip removal tool If expension-type cowling worked the way they were designed, you would simply unscrew the plastic screw and the clip would come out. Unfortunately, they seldom work correctly. Our cowling clip removal tool has a small sharp screw that screws into the plastic head and pulls the screw out. The clip will then collapse and...

Reference: LH-683

Christmas tree moulding remover

Reference: DESTOCK-FRE-080-P

Retention device: metal strip and trim caps

To prevent the corners of hubcaps from sticking out, they are often attached with adhesive tape. However, this method carries risks: adhesives can react chemically with the vehicle's paintwork, causing damage. The ideal solution? Our retaining tool, specially designed to secure hubcaps without compromising paint quality. Advantages : Optimum protection:...

Reference: DLH-511

Double-end moulding release tool

Double-end moulding release tool This heavy-duty tool is made of steel so it will not bend. It has a small rubber spacer through each end to the tool up off the glass about 1 mm. This is important for two reasons. First, it prevents the tool from scratching the glass. Secondly, it holds the end above the glass so there is less chance the tip will catch...

Reference: FRE-080-P-N168

Retention device: metal strip and trim - 2nd life

In average condition Cosmetic defects shown in the photos are present - 1 Only one item available 2nd LIFE warranty: 6 months To prevent the corners of hubcaps from sticking out, they are often attached with adhesive tape. However, this method carries risks: adhesives can react chemically with the vehicle's paintwork, causing damage. The ideal solution?...

Reference: GRAISSE-JOINT

Rubber gasket grease - 1kg

Optimize the maintenance and durability of rubber seals with our Rubber Seal Grease - 1kg, a product specially designed for bodywork professionals and garages. Applications: Ideal for maintaining door, trunk and windshield seals. Protects seals subjected to extreme thermal variations, UV and chemical exposure. Reduces squeaking and improves joint...

Reference: SSU-190-N141

Sharpening stone with handle - 2nd life

In good condition Only a few minor cosmetic flaws - 1 Only one item available 2nd LIFE warranty: 6 months With this sharpening stone equipped with an ergonomic handle, you can easily sharpen your worn blades while protecting your hands. Particularly recommended for restoring a precise cutting edge to cold-cutting knife blades, it is also suitable for...

Reference: CGE-148

Clip removal tool

Clip removal tool This tool is used to remove plastic clips on door linings. It fits easily down into the recessed area and then can slid under the head of the cowling clip. You then pull up on the center locking part and the clip can be removed. - 235 x 35 x 30 mm - 165 g