New Paint Protection Reverse Bend Blade 19mm « ULTRAWIZ »

Reference: LAC-405-N503

Suction Cup Anchor for Holding a Cutting Rope - Second Life - N503

In fair condition Overall condition: No issues Cosmetic defects shown in the photos are present — Only one item available 2nde VIE Warranty: 6 months Suction cup for holding the windscreen gasket cutting cord

Reference: LM-460

Long knife with a blade

Long knife with 1 blade Some vehicles have extra-long dashes. So you have to cut the bond from the inside. As long as the band of urethane is not too thick, you can use knives designed to cut urethane. Two lengths are available: 46 cm (standard) and 61 cm (designed for vehicles with a high windshield slope and with ewtra-long dashes). Both are made of...

Reference: AIG-125

T-handles wire threader

Just lay the wire in the notched tip and pass it through the polyurethane by pushing the tool from the inside to the outside.In the way, you can release the window. Always place the flat surface of the wire threader on the window, so that the hollow tube is not deformed.- 120 x 26 x 10 mm - 20 g

Reference: Z11RD

New COLD KNIFE BLADES SERRATED 25mm

REF-Z11RDNew ULTRAWIZ Cold knife bladeSold individually - Extra thin Cutting length: 25 mmCARTON OF 10

Reference: AP-6205

Tool declipsor

Tool declipsor SPRINGERTOOL The distinct precision curvature of the Springer Clip Removal Tool provides a varaible load distribution, safely moving the load point along the tool as more leverage is applied The tapered tip allows entry under closely fitted parts and the rounded edges avoid damage to the trim or vehicle. No matter a body shop you will be...

Reference: SPATULE-N438-DESTOCK

Right-Angle Clip-On Spatula - N438 - Clearance Sale

Note: Only 14 units in stock The right-angle clip removal tool is specially designed to facilitate the removal of clips, staples, and fasteners found on vehicles. Its angled design allows for easier access to hard-to-reach areas and enables precise work during removal operations. TIP WIDTH: 20 MM X 40 MM LONG / OPENING DIMENSIONS: 7 MM WIDE X 15 MM DEEP

Reference: CZ-444

Clip removal tool

Reference: CAISSE-N396

Storage case L: 44 cm x H: 17 cm x W: 19 cm - 2nd LIFE - N396

In very good condition Only a few minor cosmetic flaws - 1 Only one item available 2nd LIFE warranty: 6 months Storage case Length: 44cm - Width: 17cm - Height: 19cm

Reference: SK120

Replacement blade for fsl 240 pinchweld scraper l:13mm

Replacement blade for fsl 240 pinchweld scraper 13mm wide

Reference: ZAW-040

Arm wiper puller tool

REF. ZAW-040Arm wiper puller toolArm wiper puller tool with tighting screw for a simpleuse ( without additional tool)Adaptable for many cars

Reference: CB1

Brand: REPAREGLASS

Steel or nylon piano wire locking clip

The locking clip replaces the original elastic band that holds the steel or nylon piano wire in place.

Reference: AB10

9 mm snap-off blades for ol30 knives

9 mm Snap-off blades forOL30 knives (Package of 10 pieces) Olfa®knife Standard knives with a wide 18mm blade are generally too wide to accomplish fine jobs. With its retractable blade of 9mm wide, this knife allows a fine cutting with one hand. - 85 x 9 x 0,4 mm - 38 g (Package of 10 pieces)

Reference: PS-12

Bay cleaning blades (scraper not included) - 12mm

The 12 mm window cleaning blades are specially designed to remove excess adhesive from the windshield bay, particularly in curved areas and around the edges. Their specific shape allows for precise cleaning while limiting the risk of damage to the paintwork, unlike standard blades. Suitable for professional use, they offer clean and controlled work during...

Reference: CG-200NEW

Pneumatic knife with original blade

Designed to remove windshields quickly and easily, this pneumatic knife cuts through adhesive using a system of powerful oscillating blades. It offers excellent speed control thanks to its integrated regulator, allowing for precise work as needed. The blades can be rotated to 12 different positions, ensuring great versatility, even in hard-to-reach areas....

Reference: ZAW-010

Wiper puller for bolted-on wipers

Wiper puller for bolted-on wipersBecause windshield wipers have become larger, wiper arms are pressure-fitted to the posts so they will not slip. They are then secured with a nut to hold the arm in place so they will not lift. Until now, it was almost impossible to remove these wiper arms without breaking or damaging them or scratching the cowl. You no...

Reference: PSD12

Bay cleaning blades (scraper not included) - 12 mm

The 12 mm diameter windshield cleaning blades are specially designed to remove excess adhesive from the windshield seal, particularly around curves and edges. Their specific shape allows for precise cleaning while minimizing the risk of damaging the paintwork, unlike standard scraping blades. Also available in 12 mm rectangular (REF-PS-12) and Ø 6 mm...

Reference: FB194

Hook blade 110 mm

LAME A CROCHET EN U - 110 mm

Reference: AEB405-N192

Pneumatic knife: Equalizer® EXCALIBUR® DELUXE - 2nd LIFE - N192

Kit in good condition. The case may be incomplete (blades). Only cosmetic defects shown in the photos are present. Only one item available. 2nd LIFE warranty: 6 months Recommended for cutting the lower parts of the windscreen, rear windows and quarter windows. Cutting the interior of the vehicle. Compact and lighter, it is even easier to handle,...

Reference: BOB-1.5-ROLL-OUT

Round wire in a spool REPAREGLASS - ø 0,80 mm, 1500 ml

Round wire in a spool The round profile and the small diameter make this wire a real problem solver for todays cars with narrow gaps between glass and body. It has the same high tensile strength than the VKD-44but offers at the same time as much lower risk to damage interior linings and dashboards.679 Newtonø 0,80 mm, 1500 ml

Reference: RR23-N504

Ratchet for RAPTOR kit - N504 - Second Life

In good condition Only a few cosmetic flaws, as shown in the photos, are present—only one unit available 2nde VIE Warranty: 6 months -- Please note: This ratchet is not compatible with the ROLL N CUT Kit Ratchet for Raptor

Reference: DESTOCK-FRE-080-P

Retention device: metal strip and trim caps

To prevent the corners of hubcaps from sticking out, they are often attached with adhesive tape. However, this method carries risks: adhesives can react chemically with the vehicle's paintwork, causing damage. The ideal solution? Our retaining tool, specially designed to secure hubcaps without compromising paint quality. Advantages : Optimum protection:...

Reference: FSP-4PCS

Set of 4 plastic scrapers

Set of 4 plastic scrapers

Reference: LAME-STANDARD-EXC

Standard blades for Excalibur - 100 mm, 200 mm, and 300 mm

Designed for glass and windshield replacement professionals, Equalizer® standard blades are made of unbreakable mild steel, ensuring flexibility of use without risk of breakage. If they become bent, they can be easily straightened with pliers, extending their service life. They are easy and efficient to sharpen using a grinder, belt sander, file, or...

Reference: WK1S

Serrated, long, flat BTB blade, 300mm

Serrated, long, flat BTB blade, 300mm

Reference: PILE-RAPTORX4

Rechargeable batteries for RAPTOR Kit - Set of 4

Rechargeable batteries for RAPTOR kit - Warning note that these batteries are compatible with our RAPTOR kits with a serial number prior to R0005372. If in doubt, please contact us. Sold in packs of 4 For information: 4 batteries are required for the RAPTOR device.

Reference: PSI-200

Double nylon seat panel cover

Effectively protect the interior of your vehicles with this one-piece double seat cover, ideal for automotive professionals. Applications : Ideal for workshops, garages and car cleaning services. Also suitable for jobs requiring temporary protection of vehicle interiors.

Reference: FSC-350

Brand: REPAREGLASS

Special scraper

REF. FSC-350SCRAPER (without blade)To scrape the old urethane bead. This scraper is universal due to thefact it can accept different blades width ( 13 mm – 16 mm – 20 mm)and angular bladesIts locking system with roll allow a quick and easy blade replacement

Reference: JCS452

Compact C-clip remover

Compact C-clip removerC-clip removers are an item that every technician has inhis toolbox, but those C-clips removers will not alwaysfit into the tight spots and compound curves on somevehicles. The Compact C-clips remover has a flat designthat will let you use it from all sides. This handy tool isdefinitely one that no technician should be without.REF....

Reference: XL2

Long Olfa® knife with a snap-off blade

Olfa® knife Snap-off blades have known a growing success in our filed, especially during these recent years. With this knife, you can cut the urethane that is far below the dashe of most vehicles. This knife is an extra-long version of the OLF20, it is particularly suitable for car glaziers.- 280 x 40 x 20 mm- 125 g

Reference: CROCHET-N464-DESTOCK

Crochet - N464 - Clearance Sale

Please note: Only 7 units in stock The hook is a practical tool designed to facilitate the removal, handling, and extraction of various components during automotive repairs. Its shape makes it easier to reach and grasp certain parts or components that are difficult to access. With its T-shaped handle that provides a secure grip, it allows you to apply...