Square piano wire for windshield cutting - 0.7 x 0.7 mm - 44ML

Reference: 4590

Riveting Plier K39

Reference: MAILLET

Rubber hammer

Reference: CHAMB

Microfiber for glass and polishing 40 x 40 cm

Ideal for cleaning applications, high-tech and virtually indestructible. Replaces chamois and polishing cloths, machine-washable without softener. Use for car windows, car polishing, polish and polish remover.

Reference: 948

Brand: REPARBRISE

Special windshield repair scraper blades - Pack of 5

Our scraper blades will allow you to remove excess resin from the surface after your windshield repair. Pack of 5 blades

Reference: ZDK-500

Cold knife

Wheel step ladderBuilt with a chain to facilitate the setting when the wheel compartment and the wheel are very closer. Easy and fastadjusting system. Ready to use. The other advantage correspond to the fact it can be install for all vehicules contrary to the oldversion (rigid tube) which was fitting for only SUV and cars where the space between.The wheel...

Reference: Z1

Cold knife blade 19 mm

Cold knife blade- Sold individually- Cutting length: 19 mm- 18gCARTON OF 10

Reference: Z2

Cold knife blade 25 mm

Cold knife blade, extra fine- Sold individually- Cutting length: 25 mm- 18gCARTON OF 10

Reference: Z3

Cold knife blade 38 mm

Cold knife blade, extra fine- Sold individually- Cutting length: 38 mm- 20 gCARTON OF 10

Reference: Z1022

Cold knife blade

This special blade reaches the urethane between the wheel cover and the side of the windshield.Its unique shape allows you to unbond the windshield with a cold knife, without having removed the wheel cover (also bond) before. Once the windshield is removed, you can unbond the wheel cover, wihtout risking to damage the remaining material.- Sold...

Reference: PAIG-200

Wire gripping handles (corkscrew shape)

Wire gripping handlesIdeal solution to work rapidly and without problem. Feed the wire through the hole in the wedge shaft (fig A), loop it through the hole at the top of the shaft (fig B) and then bring it back into the large plastic handle. By pressing the wedge back into the handle, the wire is held in place (fig C). To shorten the wire, press down on...

Reference: AIG-300

Wire guide

The wire guide's long, narrow shaft allows positioning the wire so it prevents the dash and interior mouldings from being damaged. Recommended above all for cars with a high windshield slope or with a bottom window bond that is hardly accessible. Of course, the wire guide can also be used from the outside.- 350 x 38 x 38 mm - 220 g

Reference: CROR-S

Brand: REPAREGLASS

Ball-tipped hook, with short shaft

Ball-tipped hook, with short shaft- 210 x 35 x 35 mm - 122 g

Reference: CROR-L

Brand: REPAREGLASS

Ball-tipped hook, with long shaft

Ball-tipped hook, with long shaft- 280 x 35 x 35 mm- 160 g

Reference: CGE-148

Clip removal tool

Clip removal tool This tool is used to remove plastic clips on door linings. It fits easily down into the recessed area and then can slid under the head of the cowling clip. You then pull up on the center locking part and the clip can be removed. - 235 x 35 x 30 mm - 165 g

Reference: SGR-380

Glass scraper, with 1 RK-100A blade

Glass scraper with 1 RK-100A bladeMainly used to rapidly and entirely remove bond residues on windows that will be reinstalled. Also used to remove stickers. Simply replace the old blade by a new one, no sharpening needed.

Reference: L2

Olfa® knife

Olfa®knife This knife is made of high impact plastic, has a stainless steel blade housing and a positive locking thumb wheel so that you can set the blade at any length. The back of the knife features a rubber grip that lets the knife rest comfortably in your hand and keeps it from slipping. The famous model. - 146 x 40 x 20 mm - 110 g

Reference: XL2

Long Olfa® knife with a snap-off blade

Olfa® knife Snap-off blades have known a growing success in our filed, especially during these recent years. With this knife, you can cut the urethane that is far below the dashe of most vehicles. This knife is an extra-long version of the OLF20, it is particularly suitable for car glaziers.- 280 x 40 x 20 mm- 125 g

Reference: MS-180

Installation stick

Reference: ZAW-010

Wiper puller for bolted-on wipers

Wiper puller for bolted-on wipersBecause windshield wipers have become larger, wiper arms are pressure-fitted to the posts so they will not slip. They are then secured with a nut to hold the arm in place so they will not lift. Until now, it was almost impossible to remove these wiper arms without breaking or damaging them or scratching the cowl. You no...

Reference: SB-880

Impact-resistant safety goggles

Safety glasses It is absolutely essential to wear protective eyewear when working with glass. Our impact-resistant goggles can be conveniently worn over most glasses. The avant-garde shape of our goggles protects your eyes laterally and frontally.

Reference: OUV-CART

Urethane tube opener

Reference: SSU-190

Universal sharpening stone with handle

Reference: PSL-150-1

Suction cup deluxe sold individualy (Ø 150 mm)

Suction cup deluxe sold individualy (Ø 150 mm)Easier and safer to attach that common suction lifters with clamp lever technology.The bell shaped rubber pads already adhere onto the glass surface with slight pressing even before pressing the lever.Possibility to pass a belt through. Load capacity for each lifter is 80 kg.

Reference: 460

Butyl 460 sealant for all glass with or without seals

A polyvalent product, it can be used to waterproof both spot-welded and demountable elements (e.g. sliding roofs).  Butyl mastic sealing used for camper van roof window. The product is permanently elastic and resistant to UV rays. High solids content. Colour: black Packaging : Sold individually in 310 ml cartridges or in box of 12.

Reference: VSP-290

Window holders (forside windows)

Window holders (forside windows)Hold up the door glass while you work. Simply loop the cable over the door frame and attach the suction cups to each side of the glass.- 177 x 200 x 76 mm - 70 g

Reference: VKD-22A

Brand: REPAREGLASS

Squared cutting wire - Size 0.6mm - 22ML

Squared cutting wire REPAREGLASS Surprising, but true! The cutting force of square wire is far superior to that of common round wire. Try it out for yourself, you'll be amazed! REF-VKD-22 Square wire. 0.6 x 0.6 mm, length: 22 m, wound on plastic spool. 691 NEWTON

Reference: SD-22

Braided wire in a spool - - ø 0,80 mm - 22ML

Braided wire in a spool REPAREGLASS ø 0.80 mm, length: 22 m, Wound on a plastic spool. 1083 NEWTON The wire to be cut is twisted according to our exact specifications from three strong stainless steel wires. The wire is anodised in a typical "gold" colour.

Reference: AIG-125

T-handles wire threader

Just lay the wire in the notched tip and pass it through the polyurethane by pushing the tool from the inside to the outside.In the way, you can release the window. Always place the flat surface of the wire threader on the window, so that the hollow tube is not deformed.- 120 x 26 x 10 mm - 20 g

Reference: LH-683

Christmas tree moulding remover

Reference: GKEV

Cut-resistant knitted gloves

Our knitted gloves are tough and offer effective protection against cuts when handling glass surfaces. Latex palms provide a solid grip. Available in three sizes: M, L and XL

Reference: KPL-197

Adhesives pads for rainsensors KPL -197:For BM Classe E,Mercedes

Package of 5 pieces

Reference: KPL-193

Adhesives pads for rainsensors KPL-193: For BMW from september 2003

Package of 5 pieces

Reference: KPR-196

Adhesives pads for rainsensors KPR -196: For Chrysler, Deawoo,Kia,Honda,Hyundai, Nissan

Package of 5 pieces Dimensions :60 x 35 x 1,0 mm CHRYSLER GRAND CHEROKEE 2002DAEWOO LACETTI 2004DAEWOO NUBIRA 2003DAEWOO TACUMA/REZZO 2005HONDA ACCORD 2003-2008HONDA FR-V 2004HONDA LEGEND 2006KIA OPIRUS 2003NISSAN PRIMERA 2002

Reference: KPL-192

Adhesives pads for rainsensor KPL-192: For Renault Mégane,Nissan Micra

Package of 5 pieces

Reference: KPR-194

Adhesives pads for rainsensors KPR -194: For Volkswagen group (thickness 1mm)

Package of 5 pièces

Reference: KPR-195

Adhesives pads for rainsensors KPR -195: For Volkswagen group (thickness 1.5mm)

Package of 5 pieces

Reference: KPR-191

Adhesives pads for rainsensors KPR -191: For DB classe A,Peugeot,Cïtroen

Package of 5 pieces

Reference: KPL-190

Adhesives pads for rainsensors KPL -190: For Audi: A4,A6,A8,Q7,Opel Zafira et Corsa

Package of 5 pieces

Reference: REG-CAPLUIE

Rain / light sensor repair gel

Reference: ACT-KPR

ACTIVATOR FOR APPLICATION OF SENSOR PADS

Reference: REG-CAPLUIE2

RAIN/LIGHT CURVED SENSOR REPAIR GEL

Reference: BUSE-REG

mixing nozzles

Reference: MOUL-REG

RAIN SENSOR REPAIR MOULDS (SILICONES) 57mm x 40mm

Reference: MR5

Measure tape

Reference: 7002140

Diagonal cutting plier 150 mm

Reference: KPL-192C

Repair adhesive pads photosensor KPL-192C for BMW, RENAULT

Package of 5 pieces

Reference: KPL-154

Repair adhesive pads photosensor RÉF. KPL-154 for TOYOTA

Package of 5 pieces

Reference: KPL-166

Repair adhesive pads photosensor- Dimensions : Ø32 x 1.5 mm -for SEAT, VW

Package of 5 pieces

Reference: KPL-189B

Repair adhesive pads photosensor RÉF. KPL-189B for CHRYSLER, JEEP

Package of 5 pieces

Reference: 730362

Universal plier 250 mm

Reference: 702611200

Chain nose plier with cutter 200 mm

Reference: FSC-300SPECIAL

Brand: REPAREGLASS

Special scraper

REF. FSC-300SPECIALSCRAPER (without blade)To scrape the old urethane bead. This scraper is universal due to thefact it can accept different blades width ( 13 mm – 16 mm – 20 mm)and angular blades

Reference: SERV-OPB-PRO-NUE

Empty cart trolley without glass rack ans without foam inside the drawers