Cold knife blade 38 mm

Reference: FBS129

Scraper blade set

Jeu de 2 lames à racler. l'une large de 12 mm, l'autre de 25 mm

Reference: ZK45

ZipKnife™ COLD KNIFE

The compact ZIPKNIFE cold knife is designed for cutting in hard-to-reach areas. Uses all standard cold knife blades Without blade.

Reference: WK4ZRS

Serrated inverted deep offset BTB blade, 140mm

Serrated inverted deep offset BTB blade, 140mm

Reference: SD-22

Braided wire in a spool - - ø 0,80 mm - 22ML

Braided wire in a spool REPAREGLASS ø 0.80 mm, length: 22 m, Wound on a plastic spool. 1083 NEWTON The wire to be cut is twisted according to our exact specifications from three strong stainless steel wires. The wire is anodised in a typical "gold" colour.

Reference: PILE-RAPTORX4

Rechargeable batteries for RAPTOR Kit - Set of 4

Rechargeable batteries for RAPTOR kit - Warning note that these batteries are compatible with our RAPTOR kits with a serial number prior to R0005372. If in doubt, please contact us. Sold in packs of 4 For information: 4 batteries are required for the RAPTOR device.

Reference: HDW5634FEUTRE

Felt for RAPTOR device

Felt for RAPTOR device

Reference: TE-125

Torx t80 for arms of windshield pullers

This very wide piece is recommended for windshield removal on the BMW 5 and BMW 7 series.- 35 x 18 x 18 mm - 38 g

Reference: EGK150

Air-powered cold knife EQUALIZER® Ninja standard

The Ninja™ GT is a beefed-up version of the Ninja™. It features dual ball bearings, a more powerful engine and an exhaust silencer that routes escaping air away from the vehicle. It has a unique ability to cut under bonnets, boot lids and anything else that overhangs the glass and obstructs your ability to cut. When you encounter a bonnet, visor or boot...

Reference: FB072

Cutting blade, cranked - 45 mm

Cutting blade, cranked - 45 mm

Reference: DGL-201S

Wire gripping handle with sucker

This handle can be stuck to the glass to go around the vehicles front and grab it from the other side a real good idea and a really handy tool!

Reference: FB212

Serrated hook blade with U shape - 36 mm

Lame à crochet crantéeprofondeur de coupe : 36 mmvendue à l'unité

Reference: LAC-405

Suction cup for holding cutting rope

Reference: AIG-730

T-handles wire threader

Just lay the wire in the notched tip and pass it through the polyurethane by pushing the tool from the inside to the outside.In the way, you can release the window. Always place the flat surface of the wire threader on the window, so that the hollow tube is not deformed.- 120 x 26 x 10 mm - 20

Reference: FSC1.7POIGNEE

Pull handle for FSC1.7BAT

Reference: KFS-300

Scraper kit in plastic case

Reference: LB10S-50

Rigid segmented blades for L2 and XL2 cutters - Pack of 50

Rigid segmented blades for L2 and XL2 cutters. Sold in packs of 50 blades. Blade size: 110 x 18 x 0.5 mm - 86 g

Reference: FB154

Hook blade with U shape- 45 mm

REF-FB-154 Lame à crochet en U Profondeur de coupe 45 mmvendue à l’unité

Reference: FB194

Hook blade 110 mm

LAME A CROCHET EN U - 110 mm

Reference: CROR-L

Brand: REPAREGLASS

Ball-tipped hook, with long shaft

Ball-tipped hook, with long shaft- 280 x 35 x 35 mm- 160 g

Reference: DSS-175

One-man wire cut-out tool

One-man wire cut-out toolREPAREGLASSOne-man wire cut-out toolThis tool acts like another person sitting inside the vehicle pulling the wire back after you havemade your cutting stroke.Attached to the swivel is a spring that acts as a second person; you pull the wire out to make your cut and the springs pulls the wire back in. The spring is attached to a...

Reference: KZS-163

KZS-163 cutting nozzle tools for windshield bonding or other applications

Cutting nozzle tool for windshield bonding and other applications. The nozzle clamp makes it quick and easy to make an exact V-shaped cut in the nozzle tip of the polyurethane cartridge. This is important for good work! Because a bonding line must be applied with precision. Simply cut the tip of the nozzle to the required opening width.

Reference: AIG-300

Wire guide

The wire guide's long, narrow shaft allows positioning the wire so it prevents the dash and interior mouldings from being damaged. Recommended above all for cars with a high windshield slope or with a bottom window bond that is hardly accessible. Of course, the wire guide can also be used from the outside.- 350 x 38 x 38 mm - 220 g

Reference: ZAW-025

Arm wiper puller tool

Arm wiper puller tool

Reference: CG-200

Pneumatic cut-out

Designed to easily and rapidly remove windsheilds, it cuts the bond with oscillating blades. It is characterized by a speed control thanks to its adjuster. Blades can be put in 12 different positions. Easy to handle in narrow places. Can also serve as scraper (Delivered with one blade and one wrench).

Reference: DESTOCK-WK7L

Double manual handle for BTB blades

Double handle for BTB blade - Makes it easy to cut windshield and other glazing seals. Dimensions: 190 x 38 x 38 mm

Reference: Z1022

Cold knife blade

This special blade reaches the urethane between the wheel cover and the side of the windshield.Its unique shape allows you to unbond the windshield with a cold knife, without having removed the wheel cover (also bond) before. Once the windshield is removed, you can unbond the wheel cover, wihtout risking to damage the remaining material.- Sold...

Reference: SC316

Scraper blades for ref. FSC-300SPECIAL scrapers

16 mm scraper blades for ref. FSC-300SPECIAL- Package of 10 blades- 63 x 21 x 18 mm - 30 g

Reference: DST-734

T-handle wire threader with hole

REF-DST-734 T-handle wire threader with hole Just lay the wire in the notched tip and pass it through the polyurethane by pushing the tool from the inside to the outside.In the way, you can release the window. Always place the flat surface of the wire threader on the window, so that the hollow tube is not deformed.120 x 26 x 10 mm • 20 g

Reference: DPO-585

Rivet Stem Remover

Rivet Stem Remover It is often necessary to remove dor glasses without breaking them. Drilling out the rivet so you can remove the door glass is easy if you can remove the rivet stem. Rivet stems are made of steel and are impossible to drill out. Our rivet stem remover has contoured end so it will sit over the rivet and align perfectly with the rivet...

Reference: VNT-306

EQUALIZER® top notchtm tool

Urethane nozzle tool, top notchTM tool This tool allows you to cut rapidly and easily a proper V-notch on a urethane nozzle. This is important for an effective work! Indeed, before applying bond, a proper notch has to be cut. To use this tool, take a knife and cut the end of the nozzle tip to give yourself a bead. Next insert the top NotchTM tool inside...