Cold knife blade 25 mm

Reference: CM-536

Magnetic bowl

Magnetic bowlThe bowl can be placed almost everywhere on a vehicule because the bottom has a rubber cover to avoid scratches. The strong magnet surely holds thebowl itself and all magnetic content.Diameter:140 mm

Reference: 240

Empty RAPTOR case

Dimensions: 41 x 30 x 10 cm Sold without foam

Reference: FB209

Hook blade with L shape - 38 mm

profondeur de coupe : 38 mmvendue à l'unité

Reference: MRC1105-R3

Hook for ROLL-N-CUT kit

Crochet pour kit ROLL -N -CUT

Reference: PH-1355

Spatula curved to remove the clips

Curved Door Upholstery Remover For removing plastic fasteners in confined places. It is the same upholstery remover as the one shown above, but it is instended for use on the front part of the door where the door jam will often interfere with the removal of the door panel. Place the notch in the tool over the fastener and pry the fastener out the hole. It...

Reference: FB081

Cutting blade, cranked 60 mm

Lame à découper, courbe profondeur de coupe : 60 mm longueur totale : 85 mm vendue à l'unité

Reference: DST-53

Curved wire threader 53 mm (package at 3 pièces)

Curved wire threader:The curved wire threader anables threading of the cutting wire evenwhere the gap between glass and pinch weld is very small.This is especially helpful on side and back windows where conventionalwire threaders are often difficult to use.The curved threader can be pushed through the adhesive bead from insideto outside or from outside to...

Reference: VKS-202

Wire cut-out kit

Wire cut-out kit, with squared cutting wire.REPAREGLASS contains: - squared cutting wire, 22m, REF-VKS22 .- 1 pair of wire handles (corkscrew shape), REF-DGL200 .- 1 wire threader, REF-DST125 .- 110 x 100 x 100 mm- 375 g

Reference: Z7RV

New Paint Protection Reverse Bend Blade 19mm « ULTRAWIZ »

Nylon coating protects exposed paint from accidental blade contactIdeal for exposed glass with underside molding or encapsulationOffers the control a technician needs to cut awayfrom the glass or moldingAvailable in 3 lengths : 19 mm – 25 mm – 38 mm

Reference: ZDK-500

Cold knife

Wheel step ladderBuilt with a chain to facilitate the setting when the wheel compartment and the wheel are very closer. Easy and fastadjusting system. Ready to use. The other advantage correspond to the fact it can be install for all vehicules contrary to the oldversion (rigid tube) which was fitting for only SUV and cars where the space between.The wheel...

Reference: EEB795

EQUALIZER® blade 200 mm

EQUALIZER® blades and sheathsEQUALIZER® blade 200 mmThe blade is made of unbreakable mild steel.In case the blade bends,use pliers to straighten it up. Use a bech grinder, a strip sander, a file or a whetstone. You do not need to remove the blade to sharpen it. Our blades are made of specific material.Their round edges prevent them from being bent inside...

Reference: CS-RC14

Handable rolling Tool-box

Toolbox on wheels Size: L:62 x W:30 x H:32 cm + 10cm in height with wheels 4 drawers of 22 x 20cm

Reference: WK24ZS

Serrated Offset, BTB blade, 150mm

Serrated Offset, BTB blade, 150mm

Reference: AST-120

Telescopic magnet

Telescopic magnetWhen you work above all in the door or chassis frame of the vehicle, a screw may fall and it may be impossible to pick it up with your fingers. With this telescopic magnet, you no longer have this problem. The telescopic device is extendable from 12 (corresponding to the size of a ballpoint pen ) to 60 cm. The strong magnet is capable to...

Reference: 238

Empty RAPTOR case

Reference: AIG-730

T-handles wire threader

Just lay the wire in the notched tip and pass it through the polyurethane by pushing the tool from the inside to the outside.In the way, you can release the window. Always place the flat surface of the wire threader on the window, so that the hollow tube is not deformed.- 120 x 26 x 10 mm - 20