Cold knife blade

Reference: WK1

Long, flat BTB blade, 300mm

Long, flat BTB blade, 300mm(for general use)

Reference: FSC1.7L

FEIN electric knife + 12 blades

Fein electric knife + 9 blade: - with tool box and accessories- more lightweight- more refined- easy and rapid replacement of the wrench- speed adjuster-knife -BLADE REF-FB212 x2-BLADE REF-FB207 x3-BLADE REF-FB208 x1-BLADE REF-FB209 x1-BLADE REF-FB157 x1-BLADE REF-FB111 x1

Reference: FB083

Hook blade with U shape - 10mm

REF-FB-083 Hook blade with U shapeCutting length: 10 mmSold individually

Reference: ENO841

Cutting blade. Length: 25mm

Cutting blade. Length: 25mm - 60 x 30 x 25 mm 45 gBE CAREFUL: Ninja blades have been elaborated to fit on the Ninja knife. They should not be used with other knives.

Reference: Z9

Cold knife blade coated, extra fine 38 mm

Cold knife blade coated, extra fine - Sold individually- Cutting length: 38 mm- 20gCARTON OF 10

Reference: FSC1.7POIGNEE

Pull handle for FSC1.7BAT

Reference: GRAISSE-JOINT

Grease for rubber seal 1kg

Grease for rubber seal 1kg

Reference: FSP-4PCS

Set of 4 plastic scrapers

Set of 4 plastic scrapers

Reference: CG-200NEW

Pneumatic cut-out

Designed to easily and rapidly remove windsheilds, it cuts the bond with oscillating blades. It is characterized by a speed control thanks to its adjuster. Blades can be put in 12 different positions. Easy to handle in narrow places. Can also serve as scraper (Delivered with one blade and one wrench).

Reference: WFA-525

Arm wiper puller for rearwindows.

Arm wiper puller for rearwindows.To avoid to damage the arm wipersfrom rear vehicules, which are oftendamage with traditional arm wiper pullersEx: Peugeot 307-207, Renaultclio III, Espace Laguna, Megane,Nissan Micra et primera

Reference: PS-215

Smoother / remover tool for Silicone / Urethane beads

REF. PS-215Smoother / remover tool for Silicone / Urethane beadsThis tool allows to ensure to make a straight bead of silicone or urethane, but not only,it can remove also the old beads. The use of this product is with only one hand.

Reference: AIG-300

Wire guide

The wire guide's long, narrow shaft allows positioning the wire so it prevents the dash and interior mouldings from being damaged. Recommended above all for cars with a high windshield slope or with a bottom window bond that is hardly accessible. Of course, the wire guide can also be used from the outside.- 350 x 38 x 38 mm - 220 g

Reference: AEB405

EQUALIZER® Excalibur® deluxe

The Excalibur® is a compact, lightweight, air-powered version of the Equlizer® . Theoratically, it works in the same way as the Equlizer® .However, since it is compact and lightweight,it is even handier, especially in areas that are hard to reach andwhen you work above the level of the head.Thestiking rate is 30% higher. In this way, vibrations are...

Reference: AIG-789

Straight wire threader

Many technicians remove windshields by starting the wire through the top and bottom center of the windshield, then cutting towards each side. So as to push the cutting wire into the urethane, especially where there is a wide surface of urethane, we recommend using the wire threader. The slot (1,2 mm only) and the cutting wire are pushed together into the...

Reference: DEV-ROLL-N-CUT

ROLL-N-CUT wire reel

Reference: ZDK-500

Cold knife

Wheel step ladderBuilt with a chain to facilitate the setting when the wheel compartment and the wheel are very closer. Easy and fastadjusting system. Ready to use. The other advantage correspond to the fact it can be install for all vehicules contrary to the oldversion (rigid tube) which was fitting for only SUV and cars where the space between.The wheel...