Cold knife blade coated, extra fine 38 mm

Reference: WK28RL

RIGHT HAND INVERTED BTB BLADE 30MM

Reference: AIG-300

Wire guide

The wire guide's long, narrow shaft allows positioning the wire so it prevents the dash and interior mouldings from being damaged. Recommended above all for cars with a high windshield slope or with a bottom window bond that is hardly accessible. Of course, the wire guide can also be used from the outside.- 350 x 38 x 38 mm - 220 g

Reference: WK1S

Serrated, long, flat BTB blade, 300mm

Serrated, long, flat BTB blade, 300mm

Reference: XL2

Long Olfa® knife with a snap-off blade

Olfa® knife Snap-off blades have known a growing success in our filed, especially during these recent years. With this knife, you can cut the urethane that is far below the dashe of most vehicles. This knife is an extra-long version of the OLF20, it is particularly suitable for car glaziers.- 280 x 40 x 20 mm- 125 g

Reference: AB10

9 mm snap-off blades for ol30 knives

9 mm Snap-off blades forOL30 knives (Package of 10 pieces) Olfa®knife Standard knives with a wide 18mm blade are generally too wide to accomplish fine jobs. With its retractable blade of 9mm wide, this knife allows a fine cutting with one hand. - 85 x 9 x 0,4 mm - 38 g (Package of 10 pieces)

Reference: WK2S

Serrated, average, universal, flat BTB blade, 240mm

Serrated, average, universal, flat BTB blade, 240mm

Reference: ENO841

Cutting blade. Length: 25mm

Cutting blade. Length: 25mm - 60 x 30 x 25 mm 45 gBE CAREFUL: Ninja blades have been elaborated to fit on the Ninja knife. They should not be used with other knives.

Reference: LB10

Rigid not segmented blades for l2 and xl2 knives

Rigid not segmented blades, for L2 and XL2 knives Package of 10 pieces - 110 x 18 x 0.5 mm - 65 g

Reference: 3007-K

UltraWiz® cold knife

Fully-adjustable cold knife. The only one available on the market today. Pull on the lever to release the blade, push down on the lever to block the blade (at any height). To exchange the blade, you do not need to unscrw the screw nut anymore, so you do not waste time anymore. With this new very handy knife, you really save time.

Reference: DLH-511

Double-end moulding release tool

Double-end moulding release tool This heavy-duty tool is made of steel so it will not bend. It has a small rubber spacer through each end to the tool up off the glass about 1 mm. This is important for two reasons. First, it prevents the tool from scratching the glass. Secondly, it holds the end above the glass so there is less chance the tip will catch...

Reference: PH-1355

Spatula curved to remove the clips

Curved Door Upholstery Remover For removing plastic fasteners in confined places. It is the same upholstery remover as the one shown above, but it is instended for use on the front part of the door where the door jam will often interfere with the removal of the door panel. Place the notch in the tool over the fastener and pry the fastener out the hole. It...

Reference: ZAW-025

Arm wiper puller tool

Arm wiper puller tool

Reference: KZS-163

Standard Urethane plastic nozzle tool

Standard Urethane plastic nozzle tool

Reference: EEB795

EQUALIZER® blade 200 mm

EQUALIZER® blades and sheathsEQUALIZER® blade 200 mmThe blade is made of unbreakable mild steel.In case the blade bends,use pliers to straighten it up. Use a bech grinder, a strip sander, a file or a whetstone. You do not need to remove the blade to sharpen it. Our blades are made of specific material.Their round edges prevent them from being bent inside...

Reference: SYSTEME-PROTECTION-DE-BAIE

Pinchweld protection system

Everyprotector they used could not withstand repeated hits by a power tool blade and would jump out of the pinchweld,leaving the paint exposed to potential harm. Tape worked to some extent, but would not hold sufficient downward pressure tokeep the pinchweld protector in place.This kit includes 4 different lengths of a high impact metal that will absorb...

Reference: KFS-300

Scraper kit in plastic case