Cold knife blade, extra fine 25 mm

Reference: SD-22

Braided wire in a spool - - ø 0,80 mm - 22ML

Braided wire in a spool REPAREGLASS ø 0.80 mm, length: 22 m, Wound on a plastic spool. 1083 NEWTON The wire to be cut is twisted according to our exact specifications from three strong stainless steel wires. The wire is anodised in a typical "gold" colour.

Reference: DPO-585

Rivet Stem Remover

Rivet Stem Remover It is often necessary to remove dor glasses without breaking them. Drilling out the rivet so you can remove the door glass is easy if you can remove the rivet stem. Rivet stems are made of steel and are impossible to drill out. Our rivet stem remover has contoured end so it will sit over the rivet and align perfectly with the rivet...

Reference: EGK150

Pneumatic knife: EQUALIZER ® Ninja GT Deluxe

The Ninja™ GT Deluxe is the improved and reinforced version of the famous Ninja™ pneumatic knife. Designed for the most demanding cold cutting applications, it features two ball bearings, a more powerful motor and an exhaust silencer that redirects air away from the vehicle for optimal working comfort. Exceptional performance and versatility: Optimized...

Reference: 3007-RK

Handle for 3007-K and 3008-K

Designed to ensure a good grip and optimal control of the tool, this handle can replace the original handle supplied with the 3007-k and 3008-k cold knives in case of breakage.

Reference: WP738-E-N118

Scraper for standard door frames - 2nd life

In good condition Cosmetic defects shown in photos - 1 Only one item available 2nd LIFE warranty: 6 months Designed to effectively remove polyurethane residue, this scraper is an essential tool for professionals who install and remove glass. Equipped with a 24 mm wide hardened steel blade, it offers excellent durability and can be sharpened many times,...

Reference: TE-125

Torx t80 for arms of windshield pullers

This very wide piece is recommended for windshield removal on the BMW 5 and BMW 7 series.- 35 x 18 x 18 mm - 38 g

Reference: LH-683-N113

Lever for hubcaps - 2nd life

In good condition Only a few minor cosmetic defects appear - 1 Only one item available 2nd LIFE warranty: 6 months Removing hubcaps without the right tool can quickly damage these delicate parts. If a flat screwdriver is sometimes used, its small contact surface often causes damage and does not provide sufficient leverage. The hubcap lever solves these...

Reference: CHARG-FSC1.7

FEIN battery knife charger

Ensure fast, efficient recharging of your FEIN 18V batteries with this charger specially designed to meet the needs of professionals. Key features: Optimum compatibility: Compatible with FEIN 18V batteries RÉF. BAT18-FSC1.7 Fast charging: Reduces waiting time for continuous work without prolonged interruptions. Advanced charging technology: Protects your...

Reference: FSC-300SPECIAL

Brand: REPAREGLASS

Special scraper

REF. FSC-300SPECIALSCRAPER (without blade)To scrape the old urethane bead. This scraper is universal due to thefact it can accept different blades width ( 13 mm – 16 mm – 20 mm)and angular blades

Reference: Z10RD

New COLD KNIFE BLADES SERRATED 19mm

REF-Z10RDNew ULTRAWIZ Cold knife bladeSold individually - Extra thin Cutting length: 19 mmCARTON OF 10

Reference: Z4

Cold knife blade, extra fine 19 mm

Cold knife blade, extra fine cutting length: 19mm CARTON OF 10

Reference: FSC1.7POIGNEE

Pull handle for FEIN battery-powered knife

Highly recommended for optimal handling and better cutting control, this handle improves the precision and stability of the tool, especially during complex or prolonged cutting tasks. An essential accessory for getting the most out of your FEIN cordless knife.

Reference: SD-21

Braided wire - ø 0,80 mm - 22.5M

Braided wire21 ml REPAREGLASSBraided wire The braided wire is made of three stainless steel resistant wires that are braided to one strand. The wire is anodized (with a traditional gold colour). It has a 0.80mm diameter.

Reference: AIG-300-N51

Wire guide - Seconde LIFE

In good condition Only a few minor cosmetic defects - 1 Only one available 2nd LIFE warranty: 6 months Locking lever for wire The long, thin shaft of the locking lever for piano wire allows it to be positioned so as to avoid any damage to the dashboard, hubcaps or bodywork. Recommended especially for cars with steeply raked windshields, where the lower...

Reference: ZAW-040

Arm wiper puller tool

REF. ZAW-040Arm wiper puller toolArm wiper puller tool with tighting screw for a simpleuse ( without additional tool)Adaptable for many cars

Reference: MRC1105-R4

Ratchet for ROLL-N-CUT kit

Please note that this ratchet is not compatible with the RAPTOR Kit. 1 Ratchet For ROLL-N-CUT kit

Reference: DLH-511

Double-end moulding release tool

Double-end moulding release tool This heavy-duty tool is made of steel so it will not bend. It has a small rubber spacer through each end to the tool up off the glass about 1 mm. This is important for two reasons. First, it prevents the tool from scratching the glass. Secondly, it holds the end above the glass so there is less chance the tip will catch...

Reference: CS-RC14

Handable rolling Tool-box

Toolbox on wheels Size: L:62 x W:30 x H:32 cm + 10cm in height with wheels 4 drawers of 22 x 20cm

Reference: WK2S

Serrated, average, universal, flat BTB blade, 240mm

Serrated, average, universal, flat BTB blade, 240mm

Reference: LB10S

Rigid segmented blades for L2 and XL2 knives

Optimize your cuts with these segmented rigid blades, specially designed for use with L2 and XL2 cutters. Applications: Perfect for meticulous bodywork and mechanical work. Ideal for cutting plastics, rubber, fabrics and other materials used in the automotive industry.

Reference: WK27S

Left hand, BTB blade, 19mm

Left hand, BTB blade, 19mm

Reference: XKD-44A

Square piano wire for windshield cutting - 0.7 x 0.7 mm - 44ML

Discover our new REF-XKD-44 square piano wire, designed to offer exceptional strength and meet the most demanding needs. Applications: Used for precise cutting of windscreens and automotive glazing, this rope is a must-have for bodybuilders and garages. Its sturdy, square design ensures a firm grip and greater efficiency when removing glass and similar...

Reference: FB211

Serrated hook blade with U shape - 24 mm

Lame à crochet crantéeprofondeur de coupe : 24 mmvendue à l'unité

Reference: H600

Cutter 9 mm

9 mm cutter - supplied without bladeCompatible blades: Ref.AB-50S

Reference: FB209

Hook blade with L shape - 38 mm

profondeur de coupe : 38 mmvendue à l'unité

Reference: LM-460

Long knife with a blade

Long knife with 1 blade Some vehicles have extra-long dashes. So you have to cut the bond from the inside. As long as the band of urethane is not too thick, you can use knives designed to cut urethane. Two lengths are available: 46 cm (standard) and 61 cm (designed for vehicles with a high windshield slope and with ewtra-long dashes). Both are made of...

Reference: LB10S-50

Rigid segmented blades for L2 and XL2 cutters - Pack of 50

Rigid segmented blades for L2 and XL2 cutters. Sold in packs of 50 blades. Blade size: 110 x 18 x 0.5 mm - 86 g

Reference: CCR-819

EQUALIZER® cowling clip removal tool

EQUALIZER® cowling clip removal tool If expension-type cowling worked the way they were designed, you would simply unscrew the plastic screw and the clip would come out. Unfortunately, they seldom work correctly. Our cowling clip removal tool has a small sharp screw that screws into the plastic head and pulls the screw out. The clip will then collapse and...

Reference: WFA-525

Arm wiper puller for rearwindows.

Arm wiper puller for rearwindows.To avoid to damage the arm wipersfrom rear vehicules, which are oftendamage with traditional arm wiper pullersEx: Peugeot 307-207, Renaultclio III, Espace Laguna, Megane,Nissan Micra et primera

Reference: TB-415

Locking strip tool with 5 interchangeable eyelets

Locking strip tool With the 5 different eyelets and the pressure roller, this locking strip tool can install pratically all different types of locking strips.- 160 x Ø 25 mm - 215 g